00W's AIO Smorgasbord

[kevgib67]

For a guy that can't keep Birdsnests alive for nothing! That's 6 months of growth from an inch and a half frag with a single nub started.

This is how mine started.

 

[tbrown]

May 29th

 

[kevgib67]

May 29th

They grow like weeds, it’s hard to keep up! My first sps and I wasn’t sure how it would do. I have a monti cap and it is the same. I have trouble giving them away.

 

[00W]

They grow like weeds, it’s hard to keep up! My first sps and I wasn’t sure how it would do. I have a monti cap and it is the same. I have trouble giving them away.

I would take all I could wish I lived closer for many reasons!

 

[kevgib67]

162 really? My tank thread has been up almost 2 years and I’ve yet to hit page 5!

 

[tbrown]

I'm only at 278...

 

[tbrown]

And 22 on the new one.

 

[00W]

Goodnight everyone.
Hope y'all had a great day.
I'll see you in the morning.

 

[Kipp's Corals]

I have two big fears when its comes to the tank at this point in time. 1) overflowing tank or sump / back siphon (doing own research on that, and getting tips on how to avoid) & the initial water filling of the tank.

My question for the group this morning when everyone wakes up is on the initial fill.

When doing the initial fill how does everyone do it? For me, I would have 20G brutes. So I would need a little over 3 of them filled with RODI water. Do I just ensure each batch is roughly at the same salinity on the refractometer each time? Do I fill my tank with the rock, & sand, then add water then add salt? Gaaaah nervous LOL *help*

 

[Lowell Lemon]

Do you have snow?

No snow right now. It all melted off the last couple weeks.

 

[Kipp's Corals]

Tank 1)

AQUASCAPE 1)

PLUMBING PHOTOS 1.

2.

3.

SUMP 1.

2. 3. 4. Over flow photo

 

[Kipp's Corals]

Tank 1)

AQUASCAPE 1)

PLUMBING PHOTOS 1.

2.

3.

SUMP 1.

2. 3. 4.

Plumbing photo # 1 : I will add ball valve along the long horizontal run, to adjust flow as needed.
Plumbing Photo # 1 & 3: I will add a check valve along below the T in photo number 3 and along vertical run behind tank in photo number 1.
Sump Photo 1 & 2: Do you see any issues with heater and skimmer placement?
Overflow Photo: i know this is has to be wrong. Should i get a 1 inch x 1inch threaded PVC adapter?

P.S THIS IS ALL DRY FIT, WILL PVC CEMENT WHEN FINAL.

PLEASE REPLY WITH FEEDBACK.

 

[Remi]

I have two big fears when its comes to the tank at this point in time. 1) overflowing tank or sump / back siphon (doing own research on that, and getting tips on how to avoid) & the initial water filling of the tank.

My question for the group this morning when everyone wakes up is on the initial fill.

When doing the initial fill how does everyone do it? For me, I would have 20G brutes. So I would need a little over 3 of them filled with RODI water. Do I just ensure each batch is roughly at the same salinity on the refractometer each time? Do I fill my tank with the rock, & sand, then add water then add salt? Gaaaah nervous LOL *help*

Hi, first did you rinse the sand if you are using dry sand?
Me I would add the salt in the brutes and check salinity on each and check once diluted. For the tank, add rock, after the sand and finally the salted water. I am a beginner so...

 

[Calmwaters]

By the way, you should zoom in right about here...

I see the deer

 

[Calmwaters]

He was a two by 3 but he busted a tine and busted off the top portion of one of his main beams. He had several little eye guards

Good thing they will grow again!

 

[Calmwaters]

Good morning everyone!

 

[kevgib67]

Good morning everyone!

Good morning!

 

[kevgib67]

I have two big fears when its comes to the tank at this point in time. 1) overflowing tank or sump / back siphon (doing own research on that, and getting tips on how to avoid) & the initial water filling of the tank.

My question for the group this morning when everyone wakes up is on the initial fill.

When doing the initial fill how does everyone do it? For me, I would have 20G brutes. So I would need a little over 3 of them filled with RODI water. Do I just ensure each batch is roughly at the same salinity on the refractometer each time? Do I fill my tank with the rock, & sand, then add water then add salt? Gaaaah nervous LOL *help*

Put the rock in first, you want it on the glass., then add sand. Put a small plate on the sand and pour the water on the plate. Remove the plate. You’ll want the salinity the same in all the containers, 1.026. Sorry I can’t help you with the plumbing but I’m sure someone will chime in.

 

[Calmwaters]

So I'm curious what are some of everyone's hobbies other than aquariums?

 

[tbrown]

I have two big fears when its comes to the tank at this point in time. 1) overflowing tank or sump / back siphon (doing own research on that, and getting tips on how to avoid) & the initial water filling of the tank.

My question for the group this morning when everyone wakes up is on the initial fill.

When doing the initial fill how does everyone do it? For me, I would have 20G brutes. So I would need a little over 3 of them filled with RODI water. Do I just ensure each batch is roughly at the same salinity on the refractometer each time? Do I fill my tank with the rock, & sand, then add water then add salt? Gaaaah nervous LOL *help*

For mine, I just add plain water to about half full, then add salt. Once the salinity is where I want it, I usually let it circulate for a couple of days, then I start adding my lower rock levels. After those are in, I'll add the sand and give it another couple of days to settle out, then add the rest of the water until my tank is almost full (no water in the sump yet) and then add the rest of the rock. Last step is to top off the sump to the return-pump-off level and kick on the return pump. Usually for the first day or two while everything is still getting used to each other I won't run the return pump overnight just to make sure I can see and adjust levels as needed.