40g breeder sump setup help

[HonorableWhat]

I'm trying to set up a 40g breeder for my 100g tank and im having trouble figuring out how to do it, I was hoping you experience people could help. Here's what I'm looking g for

1 reefmat 500, skimmer, refugium, 2 sicce 3.5.

Hiw would you setup the sump If it was you?

I'd like a decently large refugium if possible

Also, what sizes would the baffles be?

 

[rsumner]

Definitely search R2R for others that have done this before. I suggest looking at the build threads because there are a ton of DIY reefers out there that have used 40-breeders for sumps.

 

[rsumner]

Also, it's not good to double post. I noticed you already have this going here: https://www.reef2reef.com/threads/40g-breeder-sump-setup.937722/

 

[HonorableWhat]

Also, it's not good to double post. I noticed you already have this going here: https://www.reef2reef.com/threads/40g-breeder-sump-setup.937722/

Yeah, I figured it would be best to just say what I was wanting to run.

I'm trying to delete that one actually xD

 

[CasperOe]

Well, you pretty much have your compartments in your thread haven’t you?

Water will flow into compartment no. 1 holding the ReefMat. Then it will flow under the first baffle into the refugium before overflowing in to the skimmer chamber where you can also fit any internal reactors before finally overflowing in to the return pump chamber.

Get all your gear, search the recommended water level for your skimmer and start building

Remember, baffles will have to be made from glass preferably to bind properly to your 40 gallon tank.

 

[HonorableWhat]

Well tha

Well, you pretty much have your compartments in your thread haven’t you?

Water will flow into compartment no. 1 holding the ReefMat. Then it will flow under the first baffle into the refugium before overflowing in to the skimmer chamber where you can also fit any internal reactors before finally overflowing in to the return pump chamber.

Get all your gear, search the recommended water level for your skimmer and start building

Remember, baffles will have to be made from glass preferably to bind properly to your 40 gallon tank.

That was the question, would it be better to have the reef mat and skimmer running together in one section, then the refugium, then the return.

But I can't really do that unless I want a really low water level refugium, or I can put my skimmer on a stand since it reccomends a 6-7 inch waterlevel

 

[CasperOe]

I’d keep the ReefMat and the Skimmer in two separate compartments for that very reason Although, i have seen many modified sumps around where the ReefMat and the skimmer are in the same compartment.

Place your ReefMat on the stand and you can pretty much adjust whatever height you want.

 

[HonorableWhat]

I’d keep the ReefMat and the Skimmer in two separate compartments for that very reason Although, i have seen many modified sumps around where the ReefMat and the skimmer are in the same compartment.

Place your ReefMat on the stand and you can pretty much adjust whatever height you want.

Yeah, I keep trying to keep the refugium as big as possible but I'm just gonna have to bite the bullet I think xD

 

[CasperOe]

Yeah, I keep trying to keep the refugium as big as possible but I'm just gonna have to bite the bullet I think xD

It’s always a compromise Look around for all the Red Sea Reefer Gen. 1 tanks that has been modified- there’s a lot of good examples on how much room it takes..

I run a Clarisea 3000 in my brand new Cade tank becuase i did not have enough room for a ReefMat without compromising on my skimmer/fuge compartment..