Adafruit.io and HS300?

[Prettymuchnow]

Hey all!

I might be trying to run before I can walk here - but I am trying to interface my Reef Pi with Adafruit IO so I can get a bit creative with an interface for my tank.

I don't see the equipment outlets for a HS300 listed in my Adafruit IO feeds for some reason. I believe the highlighted ones in the image below are all the ReefPi Feeds I can see. The others that arent highlighted are random bits I've been testing with.

I love that I can see the temp from my probe and power usage from the strip but the buttons don't come through!

Is this working as intended?

I do see an error in the reef pi error feed - does anyone think could this be related?

I'm wondering if a macro might show up instead as a workaround - not tested yet.

Thanks in advance.

 

[Prettymuchnow]

Confirmed macro's don't show up either - is adafruit.io set up for telemetry only right now?
I was hoping to make a wireless touchscreen display with a feed mode button to trigger the macro / turn off the outlets.

 

[Ranjib]

adafruit free tier restricts the number of things we can create and data emission rate, if i recall correctly.

 

[Ranjib]

macros in itself do not have any telemetry integration yet. telemetry is only available at equipment, sensor read, controller (ato, ph, temperature). It will be nice to have macro specific telemetry, but i have not thought about the specifics yet

 

[Prettymuchnow]

adafruit free tier restricts the number of things we can create and data emission rate, if i recall correctly.

Aha! I will try the paid service later today to see if it helps - otherwise I might try to use MQTT instead!

 

[Prettymuchnow]

@Ranjib So today I upgraded to adafruit IO+ just to see if it would work - and I'm still not seeing the outlets on my panel - I have disabled all other data points except for temperature. Double checked that when deleted they would reappear - so adafruit io is recieving new data from the reef pi and temperature is reading true.

I'm still seeing these errors in reef pi.
I think the ones with the red arrows may be where the issue is coming from. The others are because I disabled the feeds.

Things I am going to try next -
1. Re-Add the HS300 and setup again.
2. Install an older version of reef pi to see if the issue persists.
3. Give up and change my tactics.

If you have any ideas please let me know! I'm so excited to get this going haha.

 

[Prettymuchnow]

Update -

I have downgraded to pi 5.0 with a clean install and re-added the HS300 only. Still having the same issues.
My Adafruit io feed shows its receiving data but none of the equipment outlets that I have set up and confirmed are showing up here.

FWIW I can still see the same error in reef-pi

 

[iancarp]

Update -

I have downgraded to pi 5.0 with a clean install and re-added the HS300 only. Still having the same issues.
My Adafruit io feed shows its receiving data but none of the equipment outlets that I have set up and confirmed are showing up here.

FWIW I can still see the same error in reef-pi

I'm experiencing the same...

 

[Prettymuchnow]

I'm experiencing the same...

I'm glad I'm not alone in this!
Most of my hair is gone at this point lol.

I set up an MQTT server and had a look at the data received - I don't see any equipment in the feed at all. (But this is again probably out of my depth)

All I can see are the same three system load, mem used, undervoltage notices - Adafruit data on the left MQTT on the right. (I should really find my proper power brick...)
Previously I had my temperature probe and outlet power consumption enabled and working in adafruit io which were transmitting data - but for testing purposes I have only added 1 outlet and confirmed it is functioning from the Pi but not sending any telemetry data.

Going for a walk to have a think about this now
Will likely revert my pi install to an even earlier version to see if it has been broken somewhere along the way!