Apex atk program help

[NotFishyFishGuy]

EDIT: new problem, pump kicks on for a second then stops...
Problem below has been solved


So can anyone explain to me what the program is saying to do? I used the task configuartion to set it up but it isn’t making sense...

 

[hdsoftail1065]

@DarthSimon

 

[leepink23]

I would think the ato hi and ato lo are backwards. This is mine.

 

[leepink23]

So can anyone explain to me what the program is saying to do? I used the task configuartion to set it up but it isn’t making sense...

To Answer your question it’s saying it will be off normally, to cut on when ato hi is opened , to be off if ato lo is closed, to not run more than 5 minutes, to wait 10 seconds to cut off after being on, to continue for an extra 4 seconds after triggered off and to only run 1x every 60 minutes

 

[NotFishyFishGuy]

To Answer your question it’s saying it will be off normally, to cut on when ato hi is opened , to be off if ato lo is closed, to not run more than 5 minutes, to wait 10 seconds to cut off after being on, to continue for an extra 4 seconds after triggered off and to only run 1x every 60 minutes

Shouldn’t it be on when the low is open and off when it goes past the low?

 

[leepink23]

Shouldn’t it be on when the low is open and off when it goes past the low?

Yes that is correct.

 

[NotFishyFishGuy]

To Answer your question it’s saying it will be off normally, to cut on when ato hi is opened , to be off if ato lo is closed, to not run more than 5 minutes, to wait 10 seconds to cut off after being on, to continue for an extra 4 seconds after triggered off and to only run 1x every 60 minutes

I don’t think I flipped the switches around...I did a test and held the lower switch in the water and th e higher switch out. On the dashboard, the ATO_Low was open and the hig

 

[NotFishyFishGuy]

Yes that is correct.

Should I change the ATO low with the ATO high in the programming?

 

[NotFishyFishGuy]

Yes that is correct.

OK hows this?

 

[leepink23]

OK hows this?

Yes that would be correct

 

[NotFishyFishGuy]

Yes that would be correct

Ok ill do that

 

[leepink23]

Ok ill do that

Then after that verify it’s working correctly.

 

[NotFishyFishGuy]

Then after that verify it’s working correctly.

How do i set it to send an alarm if the water is too high? Yesterday there was a malfunction with the entire DOS and the water level was literally the same height as the rim of my tank. If the alarm on the atk had worked then i would have noticed sooner...

 

[leepink23]

How do i set it to send an alarm if the water is too high? Yesterday there was a malfunction with the entire DOS and the water level was literally the same height as the rim of my tank. If the alarm on the atk had worked then i would have noticed sooner...

Go to your email alarms and program:
If ATO_Hi closed then on
This should trigger your alarm. I receive a text if one of my alarms trigger

 

[NotFishyFishGuy]

Go to your email alarms and program:
If ATO_Hi closed then on
This should trigger your alarm. I receive a text if one of my alarms trigger

Thanks ill try that

 

[NotFishyFishGuy]

Thanks so much for everything you half already done to help me unfortunately I have another problem... apex keeps sending this don’t know what it means..

 

[leepink23]

Thanks so much for everything you half already done to help me unfortunately I have another problem... apex keeps sending this don’t know what it means..

Check and make sure you didn’t program that as your alarm

 

[NotFishyFishGuy]

Check and make sure you didn’t program that as your alarm

I also used the task configuration for that but I’ll check now

 

[NotFishyFishGuy]

Check and make sure you didn’t program that as your alarm

 

[leepink23]

It should be if Ato_hi is closed then on not ato_lo