ATO pmup

[Wolters_88]

So I have a huge storage bin that could only go in one place so I have a pmup in it running water to my ten gallon that then feeds my system. What do I need to add to this code to get it to work? I thought when it was open it would turn on with this but it’s not?

 

[blaxsun]

This is the configuration I have for my ATO/PMUP with the FMM and ATK kit. I don't know what you all have for sensors (assuming just the one), but here is my complete setup:

Fallback OFF
Set OFF
If FeedD 000 Then OFF
If LEAK CLOSED Then OFF
If ATK_RO OPEN Then OFF
If ATK_LO OPEN Then ON
If ATK_HI CLOSED Then OFF
When On > 006:00 Then OFF
Defer 000:10 Then ON
Defer 000:04 Then OFF
Min Time 030:00 Then OFF

With the "When On" line, if the total runtime exceeds 6:00min then the program will change from AUTO to OFF (meaning you will need to manually restart it). I run four (4) sensors: a leak detection sensor on the floor, the two optical sensors/float with the ATK kit and a third optical sensor to let me know when the RO reservoir gets low (as with you, I pump from a larger 15-gallon reservoir to the in-sump gravity-fed 7-gallon RO reservoir).

Hope this helps.

 

[Wolters_88]

This is the configuration I have for my ATO/PMUP with the FMM and ATK kit. I don't know what you all have for sensors (assuming just the one), but here is my complete setup:

Fallback OFF
Set OFF
If FeedD 000 Then OFF
If LEAK CLOSED Then OFF
If ATK_RO OPEN Then OFF
If ATK_LO OPEN Then ON
If ATK_HI CLOSED Then OFF
When On > 006:00 Then OFF
Defer 000:10 Then ON
Defer 000:04 Then OFF
Min Time 030:00 Then OFF

With the "When On" line, if the total runtime exceeds 6:00min then the program will change from AUTO to OFF (meaning you will need to manually restart it). I run four (4) sensors: a leak detection sensor on the floor, the two optical sensors/float with the ATK kit and a third optical sensor to let me know when the RO reservoir gets low (as with you, I pump from a larger 15-gallon reservoir to the in-sump gravity-fed 7-gallon RO reservoir).

Hope this helps.

This is my ATO. What I’m asking about is a separate pump that’s only job is to fill the ten gallon ATO. I’m just trying to get it to run 18 minutes when it’s empty.

 

[blaxsun]

This is my ATO. What I’m asking about is a separate pump that’s only job is to fill the ten gallon ATO. I’m just trying to get it to run 18 minutes when it’s empty.

What is the PMUP plugged into?

 

[Wolters_88]

What is the PMUP plugged into?

7_10

 

[blaxsun]

7_10

Is that the outlet or module number?

 

[Wolters_88]

Is that the outlet or module number?

Maybe that’s the issue? The res low is connected to my FMM and my Rod_PUMP is on the EB832 as accessory output B?

 

[blaxsun]

Maybe that’s the issue? The res low is connected to my FMM and my Rod_PUMP is on the EB832 as accessory output B?

Are you running two PMUPs? If just the one, yes - it should be plugged into your FMM. You'll also need the aux 24-volt power supply connected to the FMM to power the PMUP.

 

[Wolters_88]

I have two pmups. Ones on the FMM and the other is on my main EB832. They both work just fine. Im trying to get the second one that’s labeled RODI_PUMP to turn on for 18 minutes when the res_lo (ATO 10 gallon) is triggered open. I have attached the code and don’t know why it won’t work.

 

[Wolters_88]

Nobody huh?