Bmw manifold hose broken

[LOVEROCK]

 

[LOVEROCK]

Does anybody know what hose this is , and how to remove , losing some sleep over this , it plugs in into the manifold right at the middle of the picture , 2009 i328 bmw

 

[((FORDTECH))]

Ok should be easy fix it is just a hose after all. Go to dealer and buy a new one

 

[HeyLookItsCaps]

Wat

 

[((FORDTECH))]

That Intake looks like it’s off the car already.

 

[((FORDTECH))]

I’m assuming it’s some kind of evaporate emissions line

 

[((FORDTECH))]

And for what it’s worth if it’s not a turbo or super charged engine there is no pressure only vacuum on that line and it only looks like 1 side of clip is broken if that’s the case put it back together and don’t worrie about it will be fine

 

[((FORDTECH))]

Don’t tell anyone but I break those all the time and put back together on older focus 2.0 engine when replacing oil separator plate

 

[LOVEROCK]

And for what it’s worth if it’s not a turbo or super charged engine there is no pressure only vacuum on that line and it only looks like 1 side of clip is broken if that’s the case put it back together and don’t worrie about it will be fine

I was told on Reddit to use some sort resin to join it back together , but that would mean future maintainer to get the manifold off , eh

 

[LOVEROCK]

Ok should be easy fix it is just a hose after all. Go to dealer and buy a new one

Yeah I’m not quite sure how to remove , the hose from the car it self , that silver looking part

 

[((FORDTECH))]

I was told on Reddit to use some sort resin to join it back together , but that would mean future maintainer to get the manifold off , eh

Do not glue it at all you will regret it!!!! If for some reason that fix does not work then you will also need an intake manifold. The hose may be 100$ that Intake for bmw 1000

 

[((FORDTECH))]

Yeah I’m not quite sure how to remove , the hose from the car it self , that silver looking part

That hose is most likely part of a 15 ft line that runs the length under car to gas tank

 

[((FORDTECH))]

Yeah I’m not quite sure how to remove , the hose from the car it self , that silver looking part

Follow the line far as you can and take a pic of connector. Btw the part you broke all you literally had to do was squeeze it evenly and pop it off

 

[((FORDTECH))]

I e had trouble removing g this before so I break 1 side and reinstall with only 1 side of that clip holding it on

 

[LOVEROCK]

That hose is most likely part of a 15 ft line that runs the length under car to gas tank

do you think i have to replace all 15 feet just to repair that hose ?

 

[((FORDTECH))]

do you think i have to replace all 15 feet just to repair that hose ?

If it is 1 piece then obviously. But I work for ford soooooo it could be different. All ford Evap lines run to tank .

 

[LOVEROCK]

I e had trouble removing g this before so I break 1 side and reinstall with only 1 side of that clip holding it on

have you used some sort of reinforcement ? , you do not believe but i struggled with this point of sale connection for over 2 -3 hours , i had 3 of these in my manifold , so........ words i cant even say .

 

[LOVEROCK]

im try get some pics of it tommrow, to see if theres any kinda connection i can take off to get the hose out , been raining the whole day, probably call up dealer to confirm what type of hose this is , some people say it might be PVC? positive vent something

 

[((FORDTECH))]

have you used some sort of reinforcement ? , you do not believe but i struggled with this point of sale connection for over 2 -3 hours , i had 3 of these in my manifold , so........ words i cant even say .

No there is no reinforcement you either replace it or like I said if 1 side is good just install it

 

[((FORDTECH))]

im try get some pics of it tommrow, to see if theres any kinda connection i can take off to get the hose out , been raining the whole day, probably call up dealer to confirm what type of hose this is , some people say it might be PVC? positive vent something

Yes pvc is part of emissions system