Building a stand
- Thread starter ndz98
- Start date
- Tagged users None
Tape measure. Table saw preferably but if good with one, a circular with some clamps and a guide would work as well. Drill. Electric or air Sander or big arms. Lol. A square and a level (preferably a level as long as your stand)
Measure twice, cut once. Wood glue to all joints. (Or at least I would, may not be required though)
Hmmmmm. I think that may be it. What type of ply are you looking to use? Thickness?
Measure twice, cut once. Wood glue to all joints. (Or at least I would, may not be required though)
Hmmmmm. I think that may be it. What type of ply are you looking to use? Thickness?
OP
OP
ndz98
Valuable Member
Probably 3/4 birch if I do end up going through with it. Just not sure if it's worth building one or just buying one since I don't have all the tools.
The perk to building is being able to customize for your sump, access, maybe a frag ledge off to the side by tank, an area to run electrical and build a mounting board for controls, etc. Its all what you want to get out of it. If just need a basic stand, it may be cheaper to just outright buy one or find one used on C.list as the tool budget may add up. But then...... you've got tools for all kinda cool projects. A canopy, boxes to cover ato units, bird houses and the like. 
I've seen some pretty awesome DIY stands.
I've seen some pretty awesome DIY stands.
Wish I'd have built mine. Very limited on my sump in my stand due to the center brace by the door. Now I've got some 800+ lbs of water and rock in my way. Lol
OP
OP
ndz98
Valuable Member
And that's sort of the reason I want to build one too that way I can make it to my likings and add on extra little things. I did look online on lowes, and they have a porter cable table saw for I think $165. Maybe not the best brand ever when it comes to tools but heck, I'm sure it will be just fine for my purpose lol.The perk to building is being able to customize for your sump, access, maybe a frag ledge off to the side by tank, an area to run electrical and build a mounting board for controls, etc. Its all what you want to get out of it. If just need a basic stand, it may be cheaper to just outright buy one or find one used on C.list as the tool budget may add up. But then...... you've got tools for all kinda cool projects. A canopy, boxes to cover ato units, bird houses and the like.
I've seen some pretty awesome DIY stands.
ss95003
Active Member
I would invest in a good miter saw vs table saw. unless you plan on doing a ton of wood working you can get away without having a table saw buy just using a circular saw and a guide. If you got a compound miter saw you will thank yourself later lot of uses for around the house projects.
Get some used tools. You can get a miter saw, cordless drill/batteries for cheap.
SteveSTL
Active Member
Post where you're located or check the local reef club page. Chances are there's a woodworker near you who would be more than happy to help you for a bottle of the good stuff or beer or whatever.
SteveSTL
Active Member
You mark out the square and then grab the circular saw. There is a little handle that allows you to retract the blade guard. Retract the blade guard all the way and then line up the blade with the inside of the pencil mark. Lift the saw ever so slightly and then turn it on. Slowly plunge the blade into the wood and cut to the corner. Do that on all for sides and then finish the corners with a handsaw.
OP
OP
ndz98
Valuable Member
It makes so much more sense now lol. I've been looking for a video showing how to do that. Guess I just didn't search the right thing. It looks pretty easy as long as you take your time. Thanks!
ss95003
Active Member
you can use a guide (piece of straight wood, clamped in place) so you but straight. You aren't going to be able to follow that line dead straight with out tons of practice and then it's still easy to wobble.
Even Further
Active Member
Kreg jig & pocket screws are ideal for plywood.
OP
OP
ndz98
Valuable Member
Pics?
OP
OP
ndz98
Valuable Member
Sounds good!
