Drews BRS Dosing Pump 1.1ml x Apex Controller

[ryecoon]

Do any of you use this set up with successful results? can you give me some advice on programming the Apex Controller. Any feedback would be appreciated.

 

[ryecoon]

one more question. Do any of you dose into the overflow box? Would that make a difference?

I figured it would mix better when flowing thru the sump and into the return pump. Just wanted to see if any of you tried this method.

Thanks

 

[cilyjr]

My main supplementation is via ca reactor and kalk but I use this to add alk or ca (or anything really) overnight when I need a boost.

My program is simple
Fallback OFF
Set OFF
If Time 01:00 to 09:30 Then ON

Its set to go on when ph is low. The pump is usually but when I need to add a few ml of soda ash I'll put the tube in a little cup and click to auto. Then it will give a temp boost to ph when the tank is ok with it.

We're I to use it for regular dosing I'd probably divide the timing up alot. Because on my 240g of actual water it can still bump up ph pretty significantly even at 1.1ml/m.
Then I'd probably only let it run for a min or 2 every 15 min so as not to give a big hit to ph that prgm might look something like...

Fallback OFF
OSC 013:00/002:00/000:00 Then ON

Then as alk demand increased you could change the number, the 13:00 could become 12:30 (or lower) while the /002:00 could become /002:30 (or higher)

 

[cilyjr]

As far as adding to overflow box, it's fine but return pump chamber will work too. I wouldn't drip directly into the display if that can be avoided.

 

[ryecoon]

My main supplementation is via ca reactor and kalk but I use this to add alk or ca (or anything really) overnight when I need a boost.

My program is simple
Fallback OFF
Set OFF
If Time 01:00 to 09:30 Then ON

Its set to go on when ph is low. The pump is usually but when I need to add a few ml of soda ash I'll put the tube in a little cup and click to auto. Then it will give a temp boost to ph when the tank is ok with it.

We're I to use it for regular dosing I'd probably divide the timing up alot. Because on my 240g of actual water it can still bump up ph pretty significantly even at 1.1ml/m.
Then I'd probably only let it run for a min or 2 every 15 min so as not to give a big hit to ph that prgm might look something like...

Fallback OFF
OSC 013:00/002:00/000:00 Then ON

Then as alk demand increased you could change the number, the 13:00 could become 12:30 (or lower) while the /002:00 could become /002:30 (or higher)

Thank you. So lets say i wanted to dose something smaller through out the day like 1 ml per hour for 12 hours starting at midnight. What would the code be?

 

[Willy315]

I think you will find this helpful. It's what I use for my dosers. https://www.reeftronics.net/adpg/dosingcalc.php

 

[cilyjr]

I think you will find this helpful. It's what I use for my dosers. https://www.reeftronics.net/adpg/dosingcalc.php

Interesting

 

[don_chuwish]

Yes on the reeftronics site! I alternate Ca and Alk this way:

Doser_Ca:
Fallback OFF
OSC 000:00/007:47/112:13 Then ON
If Time 10:00 to 19:59 Then OFF
If FeedB 030 Then OFF
If Power Apex Off 000 Then OFF

Doser_Alk:

Fallback OFF
OSC 060:00/007:47/052:13 Then ON
If Time 10:00 to 19:59 Then OFF
If pH > 8.35 Then OFF
If FeedB 030 Then OFF
If Power Apex Off 000 Then OFF

Used the reeftronics code generator to determine how many minutes 'on' I needed for 60ml per night.

 

[ryecoon]

I checked my Alk yesterday it was @ 6.1 dkh then checked it 24 hours later its at 6.04 dkh. What should i start with?

 

[don_chuwish]

To figure out how much total to dose:
https://www.bulkreefsupply.com/reef-calculator/
Then decide over what time period you want to dose and use the reeftronics site to generate the code.

 

[ryecoon]

To figure out how much total to dose:
https://www.bulkreefsupply.com/reef-calculator/
Then decide over what time period you want to dose and use the reeftronics site to generate the code.

I use B-Ionic 2 part. It doesn’t give me that option. Which choice do I choose on the drop down menu?

 

[Willy315]

I use B-Ionic 2 part. It doesn’t give me that option. Which choice do I choose on the drop down menu?

ESV B-Ionic Original CA Buff Pt 1

 

[don_chuwish]

Maybe try this calculator instead:
http://reef.diesyst.com/chemcalc/chemcalc.html
I'm just trying it out myself...

 

[zack801]

I think you will find this helpful. It's what I use for my dosers. https://www.reeftronics.net/adpg/dosingcalc.php

Sorry to bump this thread but that tool is fantastic! Thank you for sharing it and thank you for whoever took the time to write that code