First Venturi Skimmer and I have no clue!

  • Thread starter Thread starter glb
  • Start date Start date
  • Tagged users None

glb

7500 Club Member
View Badges
Joined
May 12, 2013
Messages
8,141
Reaction score
3,367
Location
Miami
What state or country do you live in
Florida
Rating - 0%
0   0   0
I have an airstone skimmer in my nano so I know the basics about skimming. I just started up a 40g breeder with an SCA 301 skimmer and have a lot of questions! The tank is cycling right now with pure ammonia and Dr. Tim's One and Only and I turned on the skimmer today for the first time after waiting the recommended 48 hours. I've read a ton on skimmers the last few years but this one is so different than what I'm used to. For starters, what level would you recommend I dial in for the foam with a brand new tank? I used dry rock and dry sand so I doubt there's much to skim yet. I've read to adjust them to the top of the tube that overflows into the collection cup while the lid is off. Problem is, I've read a lot of other things too. Right now I have it about an inch above the bottom of the collection cup. Also, there are tons of micro bubbles coming from the bottom of the skimmer, and now they're everywhere. I didn't build bubble traps in my sump because I thought they weren't as big an issue anymore. Do they go away with time? How long will it take to produce skimmate in a new tank. My guess is a while if I'm still cycling. Any advice would be appreciated!!!
 
Bubbles into sump should go away with time, will not harm anything. Put water level, level with where the Cup and Body meet, so if you pulled cup off water will not overflow but be level with the top. You may have to fine tune whenever you start adding Livestock. You may want to start with GFO in a reactor right now as it is easier to keep levels in check from the start then trying to deal with it after blooms start and levels have risen. Just be patient and it will Foam one day.
 
Bubbles into sump should go away with time, will not harm anything. Put water level, level with where the Cup and Body meet, so if you pulled cup off water will not overflow but be level with the top. You may have to fine tune whenever you start adding Livestock. You may want to start with GFO in a reactor right now as it is easier to keep levels in check from the start then trying to deal with it after blooms start and levels have risen. Just be patient and it will Foam one day.
Thank you!!
 
@skim said it, start with the foam where the body meets the cup. After cleaning that's were I set mine and then about an hour later do the micro adjustments. Note when doing these micro adjustments, it's just a smidge of a turn of the dial....a mere hair of a turn.

As far as your micro bubbles, there is a chance they will reduce as the skimmer breaks in. Are they surviving after going over the baffle. I also run my sump without bubble traps, and get nothing coming over a single baffle.

As far as that skimmer, does it still come with an Atman pump? If so, I'd buy a backup now. My skimmer (SWC 160) also uses Atman, and I think I'm on pump five or six. The one potential good thing is that the last one I bought, it appears that they slightly changed the design....and I'm hoping for the better. This one has lasted more than a year. Unfortunately for you and me, there is no replacement pump that will fit without major modification.
 
@skim said it, start with the foam where the body meets the cup. After cleaning that's were I set mine and then about an hour later do the micro adjustments. Note when doing these micro adjustments, it's just a smidge of a turn of the dial....a mere hair of a turn.

As far as your micro bubbles, there is a chance they will reduce as the skimmer breaks in. Are they surviving after going over the baffle. I also run my sump without bubble traps, and get nothing coming over a single baffle.

As far as that skimmer, does it still come with an Atman pump? If so, I'd buy a backup now. My skimmer (SWC 160) also uses Atman, and I think I'm on pump five or six. The one potential good thing is that the last one I bought, it appears that they slightly changed the design....and I'm hoping for the better. This one has lasted more than a year. Unfortunately for you and me, there is no replacement pump that will fit without major modification.
Thanks. Yesterday the microbubbles were making it over all the baffles and the DT was filled with them. This morning they were only in the sump. I'll try that height and see how it goes. There probably won't be much organic material yet. I'll fire up the gfo reactor today too. After planning/building for almost 2 years, this is so much fun!!
 

IF YOU HAD TO TAKE A REEFING EXAM, WOULD YOU PASS?

  • Yes!

    Votes: 30 44.8%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 13.4%
  • No.

    Votes: 25 37.3%
  • Other (please explain).

    Votes: 3 4.5%
Back
Top