GHL ProfiLux 4 Official Announcement

[Jerel]

The current ProfiLux app is only for the 3 series.

Thanks - GHLProfilux app didn't register the P4 either . Probes going in today!

 

[enthejungle]

Hope this isn't too far off topic but was wondering if someone could tell me if this looks right. Trying to get up and running today.

 

[cbear44]

This

@fredro and @d2mini
Which version of GCC are you using? I tried both 1.0.9.2 and 1.0.9.4 and GCC doesn't show either the calibration or the Adjust temperature button for me. I did the calibrations with the P4 onscreen instructions and it worked fine but my temp is off and I'm not sure what the "ADC1" and "ADC2" number are when I go through the Temp probe calibration. Any ideas?

 

[Support@GHLUSA Verified Sponsor]

@fredro and @d2mini
Which version of GCC are you using? I tried both 1.0.9.2 and 1.0.9.4 and GCC doesn't show either the calibration or the Adjust temperature button for me. I did the calibrations with the P4 onscreen instructions and it worked fine but my temp is off and I'm not sure what the "ADC1" and "ADC2" number are when I go through the Temp probe calibration. Any ideas?

On the top ribbon, make sure Expert View is enabled.

 

[daelie]

On the top ribbon, make sure Expert View is enabled.

At least for me, hitting the adjust temperature button and trying to change it does nothing. Temperature stays the same whether I try to raise or lower in any way. I ended up just lowering my nominal temperature to compensate.

 

[cbear44]

On the top ribbon, make sure Expert View is enabled.

I'm in expert mode. I just realized I'm running 7.02 firmware - perhaps I need to upgrade it.
Temp probe is reading 23.3 but my other digital thermometer reads 24. Is there a way I adjust the ADC values?

 

[cbear44]

Updated to 7.03 and still don't see the "Calibration" or "Adjust" buttons. It flashes briefly when I click on the Sensor (see screen shot for Redox) then it disappears and the calibration data appears that I'm able to adjust actually. Good enough for now I guess. (Expert mode is on)

 

[stevo01]

What have I missed here? My p4 wont connect to my laptop. Ive tried both beta version. Im using the USB, and GCC cannot find it.

 

[fredro]

What have I missed here? My p4 wont connect to my laptop. Ive tried both beta version. Im using the USB, and GCC cannot find it.

Can you post a screenshot of the connection screen?

 

[stevo01]

Sure one sec

 

[stevo01]

 

[fredro]

Hit yes and then open the connection setting screen...

 

[fredro]

Then hit new... then choose P4

 

[d2mini]

What have I missed here? My p4 wont connect to my laptop. Ive tried both beta version. Im using the USB, and GCC cannot find it.

Check page 33 of the P4 Manual.

1. Two steps must be taken before your ProfiLux device can be operated with a PC:
   
   
   •  PC and ProfiLux must be connected with a cable via USB
     
     
   •  The PC program GCC must be set up Open the application and connect to your device.
     
     Via "Administration" -> "Connections" -> "Device Manager" you first get the "GHL Virtual Communications Port" for your device.
     

 

[stevo01]

Its still not working.

 

[Support@GHLUSA Verified Sponsor]

Stevo - can you post a picture of your device manager please, with COM ports expanded

 

[stevo01]

Stevo - can you post a picture of your device manager please, with COM ports expanded

 

[fredro]

None of your connections there are for a P4... I thinks that's why

 

[stevo01]

I think im onto something. The com port needs to be updated.

 

[stevo01]

After update the port shows up correctly.