twilliard
Tank pests..
- Joined
- Jun 3, 2015
- Messages
- 10,333
- Reaction score
- 9,516
- Location
- Central Washington
- What state or country do you live in
- Washington
Hi all!
Well after getting a lot of questions about the use of fenbendazol I figured I would write this up. This is for informational purposes and I will not be held liable for improper use. Fenbendazol must be used exactly as I instruct or run the risk of a tank crash.
Now lets get to it!
So you may ask, what is fenbendazol. Well it is a primary granular ingredient in Safegaurd 4. Here is a reference picture
I use the 4 gram packets.
1. Now don't go out and buy it just to dump the packet in the water, that would be bad!
When you open the packet you will notice the granules. This is what I separate from the powder. That is the fenbendazol. Once separated you have to crush it into a fine powder. Please wear your safety glasses.
Ok now you have this powder, what needs to be done next?
2. ALL snails, GSP's, zenias, Gorgonias, flower pots need to be put into QT. You need to observe them for any traveling hydroids for several days. This will not harm most all other corals. I have not tested with every coral or invert out there. Wish I could!
3. Next remove your carbon, slow your skimmer way down or better yet cut the air off. You need ALL equipment, pumps, powerheads, reactors, chillers RUNNING.
4. Mix up the powder in 3 cups of tank water and pour it in a high flow area slowly. The goal is to keep is suspended in the water as long as possible .
5. Wait 24 to 30 hours, you will see them all retracted. No more than 30 hours
Add fresh new carbon, don't be skimpy on this as the carbon will help pull these dead guys bad stuff out of the water. Get that skimmer fired back up.
6. Do a 25% water change after the 24-30 hours.
7. Do 10% water changes for the next 3 days after the initial 25% change.
This is the process that works the best. Hope I answered a lot of question.
-Todd
Well after getting a lot of questions about the use of fenbendazol I figured I would write this up. This is for informational purposes and I will not be held liable for improper use. Fenbendazol must be used exactly as I instruct or run the risk of a tank crash.
Now lets get to it!
So you may ask, what is fenbendazol. Well it is a primary granular ingredient in Safegaurd 4. Here is a reference picture
I use the 4 gram packets.
1. Now don't go out and buy it just to dump the packet in the water, that would be bad!
When you open the packet you will notice the granules. This is what I separate from the powder. That is the fenbendazol. Once separated you have to crush it into a fine powder. Please wear your safety glasses.
Ok now you have this powder, what needs to be done next?
2. ALL snails, GSP's, zenias, Gorgonias, flower pots need to be put into QT. You need to observe them for any traveling hydroids for several days. This will not harm most all other corals. I have not tested with every coral or invert out there. Wish I could!
3. Next remove your carbon, slow your skimmer way down or better yet cut the air off. You need ALL equipment, pumps, powerheads, reactors, chillers RUNNING.
4. Mix up the powder in 3 cups of tank water and pour it in a high flow area slowly. The goal is to keep is suspended in the water as long as possible .
5. Wait 24 to 30 hours, you will see them all retracted. No more than 30 hours
Add fresh new carbon, don't be skimpy on this as the carbon will help pull these dead guys bad stuff out of the water. Get that skimmer fired back up.
6. Do a 25% water change after the 24-30 hours.
7. Do 10% water changes for the next 3 days after the initial 25% change.
This is the process that works the best. Hope I answered a lot of question.
-Todd
Last edited by a moderator:
