how to set a program on noopsyche controller

[LowLi]

Settings below.

Note messing with the times can cause a timer error.
If i pushed the schedule below too start at 7:00 and end at 00:00. The profile would not upload it causes an error unsure why.

 

[Manose]

Settings below.

Note messing with the times can cause a timer error.
If i pushed the schedule below too start at 7:00 and end at 00:00. The profile would not upload it causes an error unsure why.

That is weird as I will have to check this out tomorrow and see if I can replicate the error.

 

[LowLi]

That is weird as I will have to check this out tomorrow and see if I can replicate the error.

yup pushing the schedule 2hrs ahead too start at 7 and end at 12 causes an error every time. least that's what it seems like for me other users with controller errors never kept updated.

 

[noopsyche]

yup pushing the schedule 2hrs ahead too start at 7 and end at 12 causes an error every time. least that's what it seems like for me other users with controller errors never kept updated.

 

[LowLi]

if i have 1% start at 7:00
then 0% at 00:00
the controller has an error ill replicate the issue today when i get home

 

[noopsyche]

The time should be set from the earlist one.
https://www.reef2reef.com/threads/how-to-set-the-correct-time.515694/

 

[LowLi]

The time should be set from the earlist one.
https://www.reef2reef.com/threads/how-to-set-the-correct-time.515694/

ohhh i get it so instead of

07:00 - 00:00

do

07:00-23:59

 

[noopsyche]

Yes, you are right.

 

[Sod Buster]

Doesn't that make sense. We need to start thinking like a programmer or the program. Nice. I'm turning on @ 7 am from now on.

 

[LowLi]

Yes, you are right.

Thank you

 

[pdiehm]

Settings below.

Note messing with the times can cause a timer error.
If i pushed the schedule below too start at 7:00 and end at 00:00. The profile would not upload it causes an error unsure why.

I finally got my light hooked up, however I cannot fo the life of me get this thing to hold a program. I tried to follow the programming video, however holding the transmit button does nothing. Right now at 10:48 pm, my light should be all blue if not close to off. But I currently have whites on at a low percentage.

 

[noopsyche]

Because you didn't link it successful. You might have one step wrong, can you share the step you did? I will figure it out.

 

[Manose]

I finally got my light hooked up, however I cannot fo the life of me get this thing to hold a program. I tried to follow the programming video, however holding the transmit button does nothing. Right now at 10:48 pm, my light should be all blue if not close to off. But I currently have whites on at a low percentage.

Make sure you do this step before you put the controller on transmit:

Operating Instructions | Noopsyche

www.noopsycheusa.com

 

[pdiehm]

The light when I set it up was solid red. I turned it on, then hit the button again and the light was flashing blue. I put the controller in manual mode and could change the individual colors.

I went into K7 and set my program for AB+. I thought I could run it on a 12 hour program but looks like it runs on an 18 hour schedule.

 

[pdiehm]

I am about to chuck this into the trash. I set my 7 stages of the program. 8, 9, 10, 6, 7, 8, 9. I go to transmit. Hit that then hit the light so it blinks. There is a video that says hold the button on the controller. The instructions don’t say anything in particular.

Right now, my light is set at 0/25/25/25/6.

But yet the white are still on.

How can anyone make something so ridiculously complicated without a phone app in this day and age?

 

[kapnkush608]

I am about to chuck this into the trash. I set my 7 stages of the program. 8, 9, 10, 6, 7, 8, 9. I go to transmit. Hit that then hit the light so it blinks. There is a video that says hold the button on the controller. The instructions don’t say anything in particular.

Right now, my light is set at 0/25/25/25/6.

But yet the white are still on.

How can anyone make something so ridiculously complicated without a phone app in this day and age?

Have to hit the buttons on the lights first.

 

[Manose]

I am about to chuck this into the trash. I set my 7 stages of the program. 8, 9, 10, 6, 7, 8, 9. I go to transmit. Hit that then hit the light so it blinks. There is a video that says hold the button on the controller. The instructions don’t say anything in particular.

Right now, my light is set at 0/25/25/25/6.

But yet the white are still on.

How can anyone make something so ridiculously complicated without a phone app in this day and age?

When the light is blinking blue it is ready to receive the signal. When you have the blinking blue light go directly to transmit not manual or anything else. When you hit transmit a couple of time by pressing the button on the controller the blue light will turn solid blue.
The controller is just different than some others but it's actually not hard to use after learning how it works.

 

[pdiehm]

Got it going. Not sure what I did but it is programmed.

 

[Manose]

Got it going. Not sure what I did but it is programmed.

That is awesome as I knew you could do it It is really easy now because you can use the built in ramp up/down feature and really get them dialed in for what ever intensity you want.

 

[JackOMalley]

Is there a definitive guide on how the SD card reader works? Can I upload/download my programs?