Is 280w normal on M80 ballast 250w Radium?

Acrofiend

Valuable Member
View Badges
Joined
Dec 31, 2016
Messages
1,634
Reaction score
592
Location
Washington
What state or country do you live in
Washington
Rating - 100%
3   0   0
I’ve read that it should be at 330w with an M80 but I’m only getting 280w. Is this normal or should I be closer to 330w?
 
Which M80 ballast are you using?

A 120 volt magnetic ANSI M80 ballast with the Radium bulb should be drawing above 300 Watts. Something does seem off.
 
Which M80 ballast are you using?

A 120 volt magnetic ANSI M80 ballast with the Radium bulb should be drawing above 300 Watts. Something does seem off.
 

Attachments

  • EDAA4053-AB50-41CD-8A27-B5DA23BB1F7D.jpeg
    EDAA4053-AB50-41CD-8A27-B5DA23BB1F7D.jpeg
    144.5 KB · Views: 56
I was using an eballast that was running at 265w before.
 
That looks like a Hamilton M80 ballast.

With that it should be drawing more than 300W. Could be a faulty bulb, failing bulb or the bulb needs to re stabilize. The capacitor in that Hamilton ballast is only used for power factor correction and doesn’t affect lamp operation. Typically those type of ballasts either work or don’t. Another thing is the wattage is dependent on the input voltage. A lower input voltage will cause the system to draw less watts.
 
Ok just tested and I’m getting 117 volts from the outlet. How can I re stabalize the bulb?
 
I’ve read that it should be at 330w with an M80 but I’m only getting 280w. Is this normal or should I be closer to 330w?
Ok, first this is not my area of expertise but if you look at this old data you will see that actual wattage is based on the bulb. Normally each brand but variations can occur in different lots of the same bulb.

That said it looks like the " old" Radiums should draw about 310-ish watts on an " hqi" ballast so 280 appears low.
There is chatter that it should draw 330w but from the limited real data I saw it was never that high.
Other bulbs yes, just not the Radium.
Ushio tested at 339w at the plug.


Now a bit of a complication. The Radium bulb of today may not be the exact same bulb as the Radium of old.

I believe it was somewhat redesigned since the m80 ballasts went out of production awhile back.

The m80 ballast itself has a beginning spec of 100v 3a.... 300w.

I'd lean to the bulb more than the ballast for the low reading but ???.

Magnetic ballasts are designed to limit lamp operating current. An ANSI M80 specification specifies a nominal 3.0 amps to the lamp. The lamp operating voltage is set by the lamp specification/design. The lamp operating voltage can be altered by the lamp’s chemistry and discharge chamber (arc tube) size. The lamp operating wattage is set by both the ballast (available current) and lamp (set voltage). With magnetic ballasts it is important to match the ballast specification with the proper lamp. They both work very closely together.
For example the Radium 250-watt lamp is designed to operate at 270-watts nominal when operated with a ballast designed to limit/provide lamp operating current to 3.0 amps same as an ANSI M80 ballast. The Radium 250-watt lamp is designed with a higher lamp operating voltage. When used with the recommended/approved magnetic ballast the lamp is allowed to operate at the designed wattage

#9
 
Last edited:
The Radium 250 kept the same electrical specs over the years.

With ballasts losses on a magnetic ANSI M80 120 volt ballast the total draw should between 310 - 330 watts. This depends on the ballast design (circuit type and coil material).

If the lamp burning position or operating conditions are changed, the lamp will require a burn in period to stabilize. Note that the Radium lamps are only designed for horizontal use.
 
I personally have had faulty halides where they draw less power than they should. Had one radium lamp and M80 ballast unexpectedly draw 270 watts at our coral farm. After close inspection we found one of the electrodes in the arc tube had a defect.
 
The Radium 250 kept the same electrical specs over the years.
Thanks.. I may have confused them with Hamiltons


Hamilton Tech's Avatar

We recently redesigned our 150 Watt 20K HQI lamps along with the 250 Watt 20K HQI & 400 Watt 20K HQI. We get a lot of positive feedback from users.

Much higher PAR and deeper blue color than before.
`

Of course that assumes the electrical specs changed as well.

Actually Hamilton changed from an almost Radium clonee to what it is today .
Spectrum is completely different.
Pointless diversion btw.
Old Hamilton.
Screenshot_20230607-094824.png


Out of curiosity I wrote to Radium.
 
Last edited:
Thank you for the responses.
I installed an older bulb and was still drawing ~280w.
 
How are you measuring the wattage draw?

Some consumer grade products don’t measure the actual power factor to calculate the actual wattage.
 
How are you measuring the wattage draw?

Some consumer grade products don’t measure the actual power factor to calculate the actual wattage.
I’m using the kill a watt meter
 

Attachments

  • 4922747D-1087-4D00-886D-0FCC03AD1B09.png
    4922747D-1087-4D00-886D-0FCC03AD1B09.png
    280.9 KB · Views: 35
How are you measuring the wattage draw?

Some consumer grade products don’t measure the actual power factor to calculate the actual wattage.
Also my apex is reading 2.6-2.8 amps. [Minus my return pump (18w), skimmer (25w), gyre (~20w)].
How can I properly read the wattage draw?
 

Attachments

  • D1464544-1128-49C0-A0D0-4CDD9D3B1813.png
    D1464544-1128-49C0-A0D0-4CDD9D3B1813.png
    109.1 KB · Views: 33
The P3 Killawatt should be reading correctly. It measures the voltage, amperage and actual power factor to calculate the wattage.

With 117 volts the wattage will be lower but yours is more than I would expect. That Hamilton ballast is a Chinese copy of the original Advance brand ANSI M80. The Advance had regulation spec’d at: +/- 12% lamp watts with input voltage +\- 5%. With your ballast the regulation could likely be worse too.
 

IF YOU HAD TO TAKE A REEFING EXAM, WOULD YOU PASS?

  • Yes!

    Votes: 30 44.8%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 13.4%
  • No.

    Votes: 25 37.3%
  • Other (please explain).

    Votes: 3 4.5%
Back
Top