Is there a factory reset on viparspectra 165

I was changing a timer on everything is right, but channel two is not coming on.
Is channel 2 turned up and not at zero? You know it's 24 hour/military time right? These sound dumb but thought I would check
 
I have that model and its very similar to the ocean revive, same controller boards and LED drivers.
let me get this right, there are 2 channels, both can go from 0 to 100, then the clock.
you have both set to 100%, but only one of the channels are on, but the other isn't.
I'm going to say you have not set the timer up correctly. the timer controls both channels independently, with an on and off time. there is a little piece of paper with instructions, let me see if I have it lying around. ah, the picture instructions are on amazon, the 4th picture.
 
I have channel one on both lights to come on at 1030, both channel two to come on at 1130, 25 blue and 2 white. Today I was changing my channel two timer and after I got a quick blip of white, and then off, now nothing on one channel 2 light. I know the instruction, but nothing mentioned about a factory reset.
 
there isn't a factory reset that I know of, I think the drivers are too weak to set to 2%. set it to at least 10%.
As for trouble shooting, right now, let them cool off (it may be over heating), set them both to 50%. and set the timers to turn on in 30 minutes.

Note: When the LEDs turn on, for each channel, there is a fan that runs in serial with each, that fan should be spinning.
If one channel is out, then only 1 fan will turn on.

If the one driver is out, open it up and simply swap the red plugs between the 2 drivers, to isolate it, then that will confirm it if the other channel begins to work.
If the timer controller is out, simply swap the 2 white plugs from the each driver that plug into the controller board, that will switch timer control between channels and 1 will become 2 and 2 will become 1.

If you have isolated it, I had 1 replacement drivers and 1 controller mailed to me for only $30, though I believe you're still under warranty.
 
I already had a par check and 50 is way to hot, my second light works fine at 2.
you need to trouble shoot first, my recommendations are not for your aquarium, but to isolate the issue. Once you figure it out, you can set it up properly.
1 heat
2, driver is weak
3 loose wire
4 and so on.

Anyway, I think it would be easier for you to use the warranty support.
 
I already had a par check and 50 is way to hot, my second light works fine at 2.
I have the 300 watt version. How high so you have them above your tank? Here's some numbers at 13.5 inches

20220617_211012.jpg


20220617_212001.jpg


With just 1% whites on it jumps up quickly. With 4% white and 72% blue I'm at 440 ish par up top
 
Anyway, I think it would be easier for you to use the warranty support.
Oh I plan to, just thought by a slim chance their would be a quicker fix. My lights are 10 inches above water with light diffuse panel as my top.
 
Ok, customer service replied and there is a reset. Now why it’s not published or can’t be found anywhere I don’t know.

So using the remote push up, down, left and right, you should see 8888 in the display. This resets time and timers. Next I unplugged the power and plugged back in, set time and timers - and both channels working.

So we shall see tomorrow.
 
Ok, customer service replied and there is a reset. Now why it’s not published or can’t be found anywhere I don’t know.

So using the remote push up, down, left and right, you should see 8888 in the display. This resets time and timers. Next I unplugged the power and plugged back in, set time and timers - and both channels working.

So we shall see tomorrow.
That's good to know..thanks for following up!
 
Do ypu press them in that order or at the same time? It's like an old nintendo code..
 
Hi all, I have the same lights, been running for at least a year with me and two with prior owner.. channel 1 for me is white, the blue stop coming on a few days ago, it’s more like a yellowish tint light now during the blue hours.
I tried the reset and put in the time again, channel 1 at 44% is white… and channel two is white… any recommendations? Lights are done…?
 

IF YOU HAD TO TAKE A REEFING EXAM, WOULD YOU PASS?

  • Yes!

    Votes: 30 44.8%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 13.4%
  • No.

    Votes: 25 37.3%
  • Other (please explain).

    Votes: 3 4.5%
Back
Top