Is this REALLY All the Bubble Output from Reef Octo Varios 4???

  • Thread starter Thread starter Kengar
  • Start date Start date
  • Tagged users None

Kengar

Well-Known Member
View Badges
Joined
Oct 28, 2009
Messages
529
Reaction score
289
Location
D.C. Metro (Gaithersburg, MD)
Rating - 0%
0   0   0
Just assembled a Reef Octopus 200 Elite INT skimmer, which includes Varios 4 pump. Testing it out and this is all I see in terms of bubbles:

KCXdyW


https://flic.kr/p/KCXdyW


This sure doesn't seem like much output!

Granted, it's in fresh water in the sump (being leak-tested), straight from tap (so no waste product), but this really seems to be "anemic." Yes? No?
 
You don't get the same action in freshwater.
Put it in saltwater and you will see a big change.
 
You just HAAAAAD to go and put another task on my plate for the day, didn't you?! :) So now I've got to go do a partial water change from the 25 I've got going -- two, really, to get enough -- so I can have some dirty test water! :)

I did recognize in post that it's fresh water knowing that that affects bubble formation/maintenance (surface tension effects, I believe), but didn't think it would make such a difference on the pump output. Foam stability and protein adhesion to the bubbles? Yes. Pump output? Surprised!
 
Add vinegar to the fresh water and you will see a reasonable display of what the bubbles will look like in salt.
 
Until you have the skimmer into saltwater and with organics to skim out, it’s not going to run like it normally would. :)
 
Yes vinegar will not produce a foam head but it'll create a ton of bubbles and if it's new it's a good idea for cleaning off any residual oils and contaminants.
 
OK, salt vs fresh made a world of difference in re bubble formation and foam production. Here are photos and videos immediately after putting the skimmer into about 5 gallons taken out of nano after stirring up substrate and doing a water change. (Click on first one to get to video; still trying to figure out link from Flickr)






Question remains, though, as to whether the overall flowrate is still on the low side. Shouldn't the chamber under the dispersion plate, inside the cylindrical ring, be fairly filled with churning water? I would have thought so. Then again, my last skimmer was a BK200 (don't recall pump, sold when my system crashed during move 8 years ago), which is admittedly at a different price-point than Reef Octo.....)

Thanks for your input.
 
Wait until you have a bio load and see how skimmate looks. I wouldn’t overthink this, this skimmer will work fine. :)
 
The depth of the water the skimmer is sitting in makes a world of difference as well. It looks like you have it sitting in only about 3" of water. Bring it up to recommended depth and you'll be dialing it back considerably.
 
Any idea off top of your head what recommmeded depth is for that skimmer? Instructions were on the sparse side and I’m in car right now so not easily able to hunt it down. Also, any idea why there were two soft tubes with the slimmer? Thirsd tube was clearly for ozone but not sure why there were two other soft silicone tubes (slightly different lengths and diameters).
 
One of the tubes is for a quick drain so you don't have to take the cup off. There should be a plug in the bottom of the cup .
 
Question remains, though, as to whether the overall flowrate is still on the low side. Shouldn't the chamber under the dispersion plate, inside the cylindrical ring, be fairly filled with churning water? I would have thought so. Then again, my last skimmer was a BK200 (don't recall pump, sold when my system crashed during move 8 years ago), which is admittedly at a different price-point than Reef Octo.....)

Thanks for your input.

There always the breakin period, which using vinegar and freshwater helps shorten.

I don't know how deep the water is suppose to be, but my guess is around 6"- 7"
 
I have a RO skimmer and and I believe it 8-9" But I would research that as it could be different :-)
 
usually skimmers like the water level between 7 to 9 inches and that's a rough number because but really depends on the maker of the skimmer. I have a Tunze 9430, a couple reef octopus, 3 or 4 skimz, 2 Nyos 160's love them, and a Bubble Magus. I believe that's it off the top of my head but they all seem to run best at those levels. By far my Nyos 160's Skims the darkest, nastiest, thickest, gunk , that stinks so bad my wife complains when I empty it. LOL. That's when you know it's dialed in and working.
 

IF YOU HAD TO TAKE A REEFING EXAM, WOULD YOU PASS?

  • Yes!

    Votes: 30 44.8%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 13.4%
  • No.

    Votes: 25 37.3%
  • Other (please explain).

    Votes: 3 4.5%
Back
Top