New 3155 Osmolator High Water Alarm Nonstop

Users Who Are Viewing This Thread (Total: 0, Members: 0, Guests: 0)

BradVol

Active Member
View Badges
Joined
Apr 3, 2020
Messages
126
Reaction score
78
Rating - 0%
0   0   0
I just got the 3155 and set it up in my sump. Plug it in for the first time and it goes straight to the Too High light being solid red with the audible alarm.

The safety switch did get submerged when I was setting it up and again when I turned off the return pump. I had both sensors mounted on the same magnet. I took the safety switch off the main magnet and mounted it above the water level when the return is off, in case the sensor getting wet is the issue.

Is it likely that the sensor getting wet is causing the alarm or is there something else going on?
 
I just went through this the other day, and I needed to slide the entire magnet assembly up and down to make it stop screaming at me. Took a while as that thing is way more sensitive than I thought, but I guess that's a good thing most of the time
 
I made sure the magnet is lined up on the safety float. The main magnet is also lined up. The black ring in the safety switch is also on the top end with the cable coming out the bottom.

I forgot to mention that when it comes on the self test has the Too Low and Pump On LEDs red. The pump never comes on, even for the priming.
 
Last edited:
Only the too low and too high lights are red, too low on start up is normal if the sensor is in water. This self test only gives valid info if the optic sensor is clean and dry. Keep in mind that the lights are recessed and if viewed at an angle you will see the lights in neighboring windows. Also, a refugium grow light will blind the sensor, optic sensors use infrared, as do grow lights that are of higher quality, this can cause a failure of the self test. After start up do you only have the too high light? Can I get a photo of how things are installed, especially clear detail of the sensor install and placement of the controller? A too high only light will be a float switch issue and usually is due to a magnetic field of some sort affecting the float, controller or wiring, this can be from electronics or it can be from how the magnet holders are installed or any other magnets nearby.
 
Only the too low and too high lights are red, too low on start up is normal if the sensor is in water. This self test only gives valid info if the optic sensor is clean and dry. Keep in mind that the lights are recessed and if viewed at an angle you will see the lights in neighboring windows. Also, a refugium grow light will blind the sensor, optic sensors use infrared, as do grow lights that are of higher quality, this can cause a failure of the self test. After start up do you only have the too high light? Can I get a photo of how things are installed, especially clear detail of the sensor install and placement of the controller? A too high only light will be a float switch issue and usually is due to a magnetic field of some sort affecting the float, controller or wiring, this can be from electronics or it can be from how the magnet holders are installed or any other magnets nearby.

Thanks Randy.

When it powers on all lights flash and the level light stays on several seconds longer. Then it goes off and nothing happens for about ten seconds. Then the alarm starts with the Too High light solid red and the Level light blinking green. After a few seconds the Level light goes off and only the Too High light stays on with the alarm sound.

I have a chaeto reactor and I've tried it with the light both off and on. I pulled the controller out of the cabinet in case there was a magnetic issue there. I've held the float switch up in my hand away from everything else and the alarm continues.

Here's pictures of the installation. Hopefully this helps with the troubleshooting.

IMG_20200520_120221.jpg
IMG_20200520_120231.jpg
IMG_20200520_120250.jpg
IMG_20200520_120300.jpg
IMG_20200520_120320.jpg
 
Everything looks correct, as long as the float switch magnet is at least 4" from any other magnet, that would be OK. For the sake of argument, would you or have you tried just taking the controller and sensors to say the kitchen and away from all magnets, sensors off the magnet holders. You can use just a bowl or cup of water to test the optic sensor and here for testing I use a plain wood clothespin to hold down the float, it perfectly fills the space between the post end and bobber. This test would let us rule out a magnetic field from something in the cabinet completely.
 
I took it to the dining room and there's nothing in there that could cause interference. I didn't attach the pump, but had everything else.

The alarm still went off. I tried several times to reset the float or hold it down or move it around. Nothing changed it. Can the sensor be tested with a volt meter?

The optical sensor turned on the Level light or had it flashing by moving the level in the water. Taking it out of the water had no light on except the Too High light with the alarm.
IMG_20200520_154411.jpg
 
It can be tested with an ohm meter or continuity alarm, you would just unplug it inside and cycle the float, it should be basically on and off, infinite ohms to low/no ohms. I also don't want you to have undo hassle, if you email me your invoice I would exchange it, but if you want to continue testing, I can send a float if that is it.
 
It's showing open line in both positions, no matter what I do with the float valve. Looks like the float switch is bad unless you think otherwise. I assume it's not a continuous circuit in the alarm position, but instead the open line turns the alarm on.

I'm fine with whatever you would like to do to take care of it. I'll send you my purchase info in a private message.
 

IF YOU HAD TO TAKE A REEFING EXAM, WOULD YOU PASS?

  • Yes!

    Votes: 30 44.8%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 13.4%
  • No.

    Votes: 25 37.3%
  • Other (please explain).

    Votes: 3 4.5%
Back
Top