- Joined
- Jan 13, 2021
- Messages
- 478
- Reaction score
- 381
- Location
- FL
- What state or country do you live in
- Florida
Hey buddy I'll give you some advice, as I bought the same tank/stand a few weeks ago.
Build a new stand. That thing is garbage. If you take the top off (a few screws hold it under the bottom) you'll see how shoddy the craftsmanship is. I was planning to make a video of it, because It is brand new from mainland, and seems to be a popular option for a good price when it goes on sale.. but I'm not so sure about it's stability.
Full disclaimer, I bought the setup intending to use the stand, but upon taking it apart, it would have cost the same to reinforce it than to just build a new stand. Also because the of the design I wasn't sure it would even be solid with the reinforcements.
A few things I remember about the stand:
1. All of the horizontal supports (not visible) have gaps. They DO NOT touch from side to side on main support panels. Many of them were nailed in place 1/8th of an inch too high or low, causing issues with flush construction. Probably what is causing your top to be unlevel.
2. Much of the panels are unsquare or not level. My cabinet doors were squared up, but the gaps were not even. I can see the same issue in your first picture.
3. Pretty much anything you can't see with your eye is unpainted. This is a big problem when the main construction is particle board. The top of the main supporting walls are not painted under the main shelf. The entire underside of every panel and the stand is UNPAINTED. Open your cabinet and take a look at the bottom edge, they're not even painted lol. Soooo cheap. Most of the inside is only airbrushed with such a thin layer you can see the wood pattern though it. Water will easily find its way into these stand and cause catastrophic failure.
4. The actual width and depth of the tank over hang ALL main supports that go direct to the ground. 850lbs of water is going to be supported by the outside frame of 5/8 inch particle board. ( I made a thread about this awhile back)
I wound up keeping it because it was on sale for $350 and I got an extra 50% off since it was missing the glass top and lights. The tank alone is a nice buy at $175, and my wife uses the stand in the kitchen to hold house plants lol
Build a new stand. That thing is garbage. If you take the top off (a few screws hold it under the bottom) you'll see how shoddy the craftsmanship is. I was planning to make a video of it, because It is brand new from mainland, and seems to be a popular option for a good price when it goes on sale.. but I'm not so sure about it's stability.
Full disclaimer, I bought the setup intending to use the stand, but upon taking it apart, it would have cost the same to reinforce it than to just build a new stand. Also because the of the design I wasn't sure it would even be solid with the reinforcements.
A few things I remember about the stand:
1. All of the horizontal supports (not visible) have gaps. They DO NOT touch from side to side on main support panels. Many of them were nailed in place 1/8th of an inch too high or low, causing issues with flush construction. Probably what is causing your top to be unlevel.
2. Much of the panels are unsquare or not level. My cabinet doors were squared up, but the gaps were not even. I can see the same issue in your first picture.
3. Pretty much anything you can't see with your eye is unpainted. This is a big problem when the main construction is particle board. The top of the main supporting walls are not painted under the main shelf. The entire underside of every panel and the stand is UNPAINTED. Open your cabinet and take a look at the bottom edge, they're not even painted lol. Soooo cheap. Most of the inside is only airbrushed with such a thin layer you can see the wood pattern though it. Water will easily find its way into these stand and cause catastrophic failure.
4. The actual width and depth of the tank over hang ALL main supports that go direct to the ground. 850lbs of water is going to be supported by the outside frame of 5/8 inch particle board. ( I made a thread about this awhile back)
I wound up keeping it because it was on sale for $350 and I got an extra 50% off since it was missing the glass top and lights. The tank alone is a nice buy at $175, and my wife uses the stand in the kitchen to hold house plants lol
Last edited:
.

