Pickupman66 Reef-pi Build

[pickupman66]

seems to have stuck here. been at this step for a few minutes.

 

[bishoptf]

seems to have stuck here. been at this step for a few minutes.

Let it run for a few and see it it completes, canceling it out when upgrading is not the best to cancel out, see if it will complete...

 

[pickupman66]

I totally understand. it is still at that same spot.

 

[bishoptf]

I totally understand. it is still at that same spot.

open another ssh session and do a top command and see what it says its working on...

top

 

[pickupman66]

nope. cannot connect to it any longer. I can ping it but cannot open a new putty session nor even open a remote desktop session with it. it is in the closet so I cannot open a local session on it. (no monitor)

 

[bishoptf]

nope. cannot connect to it any longer. I can ping it but cannot open a new putty session nor even open a remote desktop session with it. it is in the closet so I cannot open a local session on it. (no monitor)

Well I think you have a unhappy camper, could be lots of things but something is not happy, give it a few more minutes then pull the plug and see if it starts back up. When it does lets do these one at a time:

sudo apt-get update
sudo apt-get upgrade
sudo apt-get dist-upgrade

If any of those spit out something wonky just post it and we will go from there...

 

[pickupman66]

 

[bishoptf]

run the command

sudo dpkg --configure -a

Then see if that resolves and try again, one command at a time...

 

[pickupman66]

pi@raspberrypi:~ $ sudo dpkg --configure -a
Setting up gtk2-engines-clearlookspix:armhf (1:2.20.7) ...
Setting up idle-python2.7 (2.7.13-2+deb9u3) ...
Setting up libxapian30:armhf (1.4.3-2+deb9u2) ...
Setting up libwbclient0:armhf (2:4.5.12+dfsg-2+deb9u4) ...
Setting up rpi-chromium-mods (20190103) ...
Setting up apt-transport-https (1.4.9) ...
Setting up samba-libs:armhf (2:4.5.12+dfsg-2+deb9u4) ...
Setting up bluez-firmware (1.2-3+rpt7) ...
Processing triggers for mime-support (3.60) ...
Processing triggers for desktop-file-utils (0.23-1) ...
dpkg: dependency problems prevent configuration of libraspberrypi-doc:
libraspberrypi-doc depends on libraspberrypi0 (= 1.20181112-1); however:
Version of libraspberrypi0 on system is 1.20180817-1.

dpkg: error processing package libraspberrypi-doc (--configure):
dependency problems - leaving unconfigured
Setting up libarchive13:armhf (3.2.2-2+deb9u1) ...
Processing triggers for install-info (6.3.0.dfsg.1-1+b1) ...
Setting up dhcpcd5 (1:6.11.5-1+rpt7) ...
Setting up tzdata (2018i-0+deb9u1) ...
Debconf/Priority.pm did not return a true value at /usr/share/perl5/Debconf/Config.pm line 9.
BEGIN failed--compilation aborted at /usr/share/perl5/Debconf/Config.pm line 9.
Compilation failed in require at /usr/share/perl5/Debconf/Log.pm line 10.
Compilation failed in require at /usr/share/perl5/Debconf/Db.pm line 7.
BEGIN failed--compilation aborted at /usr/share/perl5/Debconf/Db.pm line 7.
Compilation failed in require at /usr/share/debconf/frontend line 6.
BEGIN failed--compilation aborted at /usr/share/debconf/frontend line 6.
dpkg: error processing package tzdata (--configure):
subprocess installed post-installation script returned error exit status 5
Setting up libfuse2:armhf (2.9.7-1+deb9u2) ...
dpkg: error processing package libfuse2:armhf (--configure):
unable to open triggers ci file '/var/lib/dpkg/info/libfuse2:armhf.triggers': Input/output error
Setting up geany-common (1.29-1+rpt2) ...
dpkg: error processing package geany-common (--configure):
unable to open triggers ci file '/var/lib/dpkg/info/geany-common.triggers': Input/output error
Setting up samba-common (2:4.5.12+dfsg-2+deb9u4) ...
dpkg: error processing package samba-common (--configure):
unable to open triggers ci file '/var/lib/dpkg/info/samba-common.triggers': Input/output error
Setting up libsmbclient:armhf (2:4.5.12+dfsg-2+deb9u4) ...
dpkg: error processing package libsmbclient:armhf (--configure):
unable to open triggers ci file '/var/lib/dpkg/info/libsmbclient:armhf.triggers': Input/output error
Setting up libssl1.0.2:armhf (1.0.2q-1~deb9u1) ...
dpkg: error processing package libssl1.0.2:armhf (--configure):
unable to open triggers ci file '/var/lib/dpkg/info/libssl1.0.2:armhf.triggers': Input/output error
Processing triggers for libc-bin (2.24-11+deb9u3) ...
dpkg: unrecoverable fatal error, aborting:
unable to flush updated status of 'libc-bin': Read-only file system

 

[pickupman66]

FYI, at this time Reefpi is DOWN.
pi@raspberrypi:~ $ sudo systemctl status reef-pi.service
-bash: /usr/bin/sudo: Input/output error

 

[bishoptf]

FYI, at this time Reefpi is DOWN.
pi@raspberrypi:~ $ sudo systemctl status reef-pi.service
-bash: /usr/bin/sudo: Input/output error

Yeah understand, if you try to manually start it up I assume it will not start?

 

[pickupman66]

That is correct.

 

[bishoptf]

That is correct.

Trying to see what is the least path to resistance...

 

[pickupman66]

NO worries. so oddly enough heater controlled outlet is on. and the ATO is off. I will move the heater over to an always on plug and let it run its own thermostat for tonight. I can get into it remotely tomorrow but something tells it will all need to be reinstalled tomorrow evening.

 

[pickupman66]

NO worries. so oddly enough heater controlled outlet is on. and the ATO is off. I will move the heater over to an always on plug and let it run its own thermostat for tonight. I can get into it remotely tomorrow but something tells it will all need to be reinstalled tomorrow evening.

 

[bishoptf]

lets try to do this...

sudo rm /var/lib/dpkg/lock

then

do this

sudo dpkg --reconfigure -a

if that all comes back clean, try running the upgrade commands again...

 

[pickupman66]

Thanks Tom. I'll run these tomorrow either remotely or when I get home in the evening after 7pm cst. For now the return and heater moved over to a redundant power supply outside of any controller.

 

[bishoptf]

Thanks Tom. I'll run these tomorrow either remotely or when I get home in the evening after 7pm cst. For now the return and heater moved over to a redundant power supply outside of any controller.

Understand, willing to help get this cleared up...I think those commands may get us back to where we want...I'll be around tomorrow evening, just ping me when your ready to poke at it some more...

by the way I'm from North Georgia , driven over monteagle so many times I could probably do it in my sleep, really think Tenn is a pretty state.

 

[pickupman66]

Thanks again. It will not connect today via SSH from my desk so I will have to wait until this evening to mess with it.

 

[bishoptf]

Thanks again. It will not connect today via SSH from my desk so I will have to wait until this evening to mess with it.

Bummer, it's not a happy camper right now but I think we should be able to get it going again.