reef-pi :: An opensource reef tank controller based on Raspberry Pi.

[Erica-Renee]

I see the IR Control thing as another gadget that really has no true use. My Lights have ir capability but it has NEVER Been used.. All 5 of the remotes are still in there plastic. Lights are set and left alone . I see no reason to need to sit on the couch .. OHH WAIT We can sit on the couch and control our tank with reef-pi...

To the if the internet is down or no internet in the house.. Raspberry pi itself can create a hot spot or its own network , This would solve the no network thing ...

 

[Ranjib]

Ok, I broke it trying to do an upgrade to the Beta 3

I ended up uninstalling the old version, then installed the new one, I get this now...

ignore the host name, It's a Ras 3 b

TIA

Enable i2c and restart reef-pi
Enable i2c protocol using

sudo raspi-config

More: https://learn.adafruit.com/adafruits-raspberry-pi-lesson-4-gpio-setup/configuring-i2c

 

[Ranjib]

I see the IR Control thing as another gadget that really has no true use. My Lights have ir capability but it has NEVER Been used.. All 5 of the remotes are still in there plastic. Lights are set and left alone . I see no reason to need to sit on the couch .. OHH WAIT We can sit on the couch and control our tank with reef-pi...

To the if the internet is down or no internet in the house.. Raspberry pi itself can create a hot spot or its own network , This would solve the no network thing ...

I was talking about situation where you have setup pi to connect to home WiFi, but for some reason it’s not accessible viaduct to wireless hiccups .. as emergency measure . Currently I use a mechanical push button to restart the network for such scenarios

 

[LionHeart2017]

My first gadget is ATO, not attached to a reef-pi yet but in the future for monitoring hopefully it will be, this is a twin float so if the first float get stuck the second will cut the pump

 

[Ranjib]

My first gadget is ATO, not attached to a reef-pi yet but in the future for monitoring hopefully it will be, this is a twin float so if the first float get stuck the second will cut the pump

Very nice . thank you for sharing

 

[LionHeart2017]

No problems Ranjib, it's because of this thread I felt confident enough to to start tinkering in electronics, I saved a good £60 building it myself[emoji3]

 

[Erica-Renee]

I was talking about situation where you have setup pi to connect to home WiFi, but for some reason it’s not accessible viaduct to wireless hiccups .. as emergency measure . Currently I use a mechanical push button to restart the network for such scenarios

on 2.0.0-beta-3's dashboard the temperature chart doesn't load for me. Going to temperature tab will load the chart but it goes away again if i reload the page

You might need to go into dashboard settings .. Remove the temp dashboard , reload reef-pi refresh browser then put them back... If that does not work resetting the database in the troubleshooting guide might be needed...

 

[Ranjib]

on 2.0.0-beta-3's dashboard the temperature chart doesn't load for me. Going to temperature tab will load the chart but it goes away again if i reload the page

Go to Configuration -> Dashboard
And update the dashboard config. Make sure you select the write temperature probe from drop down when you select tc (temperature controller usage, i.e. heater & cooler + average hourly temperature) or temperature (latest 180 values of the sensor). If you have already done, that, then something else is wrong, share the screen shot of your dashboard configuration in that case

 

[Ranjib]

Set 2 row and 2 column layout. And then click the tc/temperature dropdown. Each cell in the layout (row x column) can have a chart type (tc, ato, temperature) and a specific id for the chart (like temp sensor name or ato name etc) . You dont need to delete or restart anything. Just configure, hit "save" and go to dashboard tab, and things should work

 

[Erica-Renee]

@Ranjib thanks I tried reconfiguring the dashboard but still same issue. Could it be something with 2.0.0-beta-3 update. Wondering if anyone who recently updated is having this issue or if it’s just something in my system

Not having this issue , I did the update earlier today...

 

[Ranjib]

@Ranjib thanks I tried reconfiguring the dashboard but still same issue. Could it be something with 2.0.0-beta-3 update. Wondering if anyone who recently updated is having this issue or if it’s just something in my system

Can you post a photo of your dashboard config, and your temperature tab?

 

[Ranjib]

@Ranjib thanks I tried reconfiguring the dashboard but still same issue. Could it be something with 2.0.0-beta-3 update. Wondering if anyone who recently updated is having this issue or if it’s just something in my system

This videos shows how to reconfigure the dashboard, the exact steps are at around 3:20

 

[HM3105]

Am I correct that seeing this on the temp tab means the pi is not reading my probes? When I say "this" I mean on the "sensor" drop down menu there is nothing listed.

 

[sector9]

I have issues with my temperature graph displaying on the dashboard for beta 3 too. If I refresh my reefpi page in my browser, temp graph is missing. If I go to the temp tab then back to the dashboard, it appears...

 

[neohusky]

Let me think about this, i.e. let me come up with a IR support first that can be customized by users, and see if that alone can help you control the LED..
Thank you for the feedback

Thanks for thinking about it.
I can certainly understand not wanting to bloat it up.
This why I was looking to at a solution which was as generic as possible and leverage off modules/components that already exist. I don’t know whether a scheduler component that can send any command for ‘other connected’ devices. I’m thinking Ethernet/wifi, ir etc.

In terms of ir control for reef-Pi for internet down: Researching over the past few I found that adding lirc support wouldn’t be difficult and there are already many hardware options for Pi/Arduino that would add the functionality with minimal trouble.

As always it’s your time and work to integrate this software side that will make this difficult.

 

[janos]

Hi to all,something went wrong with the new 3 update.remove 5 times,reinstall 5 times and always the same problem,any help or just redirect to the right reading.Thank you

 

[janos]

On the good news site fund 2 case ,one for pi and one for the relay board

 

[Ranjib]

Am I correct that seeing this on the temp tab means the pi is not reading my probes? When I say "this" I mean on the "sensor" drop down menu there is nothing listed.

Yes. You can check the same in raspberry pi using

ls /sys/bus/w1/devices/

Each sensor should have a single 28-xxxxxxxx entry

 

[sjeff35]

Enable i2c and restart reef-pi
Enable i2c protocol using

sudo raspi-config

More: https://learn.adafruit.com/adafruits-raspberry-pi-lesson-4-gpio-setup/configuring-i2c

Thanks, that was it!!!

 

[janos]

One more pic.No clue what is that.i type 192.168.1.13 that is my Reef-pi address on my home network,and this come up.