BigRedSquid
Active Member
Has anyone had problems with there lights power level reset to full power from where they originally set it at
Reef Radiance led light..OMG..What a light....
- Thread starter Budman's Corals
- Start date
- Tagged users None
scruggyj
Active Member
Here is a quick video of my 180. I have 3x 155s on it. Had them since early March 2014. They are great lights and a great price.
[video=youtube;RehIvnIhDB8]https://www.youtube.com/watch?v=RehIvnIhDB8[/video]
[video=youtube;RehIvnIhDB8]https://www.youtube.com/watch?v=RehIvnIhDB8[/video]
swk
Well-Known Member
2nd lumentek 180 arrived today. Hanging system is a bit ghetto, but I have drawn up a plan using a reclaimed railroad tie and some all thread. Should be killer once I get it together. So here it is for now and will post an update once things are in place.
Thanks again rick.
2nd lumentek 180 arrived today. Hanging system is a bit ghetto, but I have drawn up a plan using a reclaimed railroad tie and some all thread. Should be killer once I get it together. So here it is for now and will post an update once things are in place.
Thanks again rick.
Here's my stand for my LumenTek Pro180 @24x36" It also comes in a 24x48"
Last edited:
The Flying Turkey
Active Member
So Rick sent me a new controller for my Lumentek 120. The installation took less than 10 minutes with only a Phillips screw driver.
I set the light on my desk and removed the screws from around all 4 sides. The top lifted right off. Mounted to the top are the power supplies and there are wires that connect the power supplies to the controller and LEDs which are mounted in the base of the unit. These wires have plugs that are easy to disconnect, but the plugs are the same size and shape, so you have to make sure you put the correct plug into the correct socket. I marked the wires before I took the plugs apart so I knew which ones went back together.
Once the plugs were disconnected and the top was out of the way, access to the controller was easy.
The old controller had a green & yellow wire (ground) that was soldered to the controller on one end, and the other end of the wire was screwed to the aluminium heat sink over the LED's. The new controller no longer has this wire so I just unscrewed the wire, and put the screw back in the hole.
There are 4 screws that hold the controller in place. I removed them and the controller came right out. I popped the new one in, reconnected all the plugs, and put the unit back together.
***Note: Take advantage of having the unit sitting on your desk, and program the custom mode while seated. It takes a while to program every 10 minutes over a 12 hour period. ***
I have to say the quality of the internal components is quite good and I was pleasantly surprised. And actually, there were very few internal parts. A couple of power supplies, the controller, an aluminium heat sink, and the LED's. I expect this light to last a long time.
So far so good. I haven't had any issues with the controller switching modes. I'm still watching the clock though, looking for any time loss or gain.
I'll update again soon.
I set the light on my desk and removed the screws from around all 4 sides. The top lifted right off. Mounted to the top are the power supplies and there are wires that connect the power supplies to the controller and LEDs which are mounted in the base of the unit. These wires have plugs that are easy to disconnect, but the plugs are the same size and shape, so you have to make sure you put the correct plug into the correct socket. I marked the wires before I took the plugs apart so I knew which ones went back together.
Once the plugs were disconnected and the top was out of the way, access to the controller was easy.
The old controller had a green & yellow wire (ground) that was soldered to the controller on one end, and the other end of the wire was screwed to the aluminium heat sink over the LED's. The new controller no longer has this wire so I just unscrewed the wire, and put the screw back in the hole.
There are 4 screws that hold the controller in place. I removed them and the controller came right out. I popped the new one in, reconnected all the plugs, and put the unit back together.
***Note: Take advantage of having the unit sitting on your desk, and program the custom mode while seated. It takes a while to program every 10 minutes over a 12 hour period. ***
I have to say the quality of the internal components is quite good and I was pleasantly surprised. And actually, there were very few internal parts. A couple of power supplies, the controller, an aluminium heat sink, and the LED's. I expect this light to last a long time.
So far so good. I haven't had any issues with the controller switching modes. I'm still watching the clock though, looking for any time loss or gain.
I'll update again soon.
BigRedSquid
Active Member
Ive been having issues with time and power and increasing
chicagobears2010
Active Member
Curious what u got them set at...nice vid
Sorry for the iPhone 4s pics, I spent all my money on this upgrade and not a camera 
But my LPS & and only 1 Purple Birds nest are doing amazing!
But my LPS & and only 1 Purple Birds nest are doing amazing!
That's strange. I'm sure it's not the sight but your antivirus software. Does it give you the choice of whether or not you trust the sight?
kaoscoder
Community Member
- Joined
- Feb 26, 2013
- Messages
- 57
- Reaction score
- 0
- Location
- Mesa
- What state or country do you live in
- Arizona
You can bypass the block by excluding the IP address. It's likely a false positive. Still, Malwarebytes is a very popular AV product.. it would behoove the owner of the site to get it resolved.
GrizFyrFyter
Well-Known Member
- Joined
- Jan 29, 2014
- Messages
- 653
- Reaction score
- 410
- Location
- Modesto, CA
- What state or country do you live in
- California
That's sounds like a good idea lol
zwulfke
Reefer Extraordinaire
24" Dimmable Automatic Sunrise Programmable Timer Reef Coral LED Aquarium Light | eBay
Rick you getting ripped off of your patent or ideas ???
Rick you getting ripped off of your patent or ideas ???
As an eBay Associate we earn from qualifying purchases.
