Reefmat aftermarket alternative?

[aaron186]

I have a ReefMat 500 and I’m burning through filter rolls in 2-3 weeks on my tank. I was wondering if there’s an aftermarket/cheaper alternative than buying the read sea rolls?

 

[CasperOe]

If I am not mistaken, you already have a previous post in this subject?

 

[aaron186]

It’s asking a different question but I didn’t realize I was limited to only 1 post

 

[WhatCouldGoWrong71]

Yeah, Steve over at [email protected] can help you out. I just order his rolls for my 5&12 Reefmat. However, his is a 2 inch vs the 1.5 (or whatever sizes they are) . He shared the contact with me of someone who was printing an adapter tube but he hasn’t replied to my emails. I haven’t tried it on the smaller tube.

I have been getting a month out of both my 1200 and my 500. However, the tank that has the 500 recently had a precipitation event, and is now going through rolls in less then a week. I’m likely going to have to take all the plumbing, UV, etc, off the tank and clean out the lines. There is a coating in all the plumbing that is now really causing me to go through some fleece. I’m going to give it one more roll to see if it cleans itself out… if you follow the dates, you can clearly see where the event took place… sigh…

 

[WhatCouldGoWrong71]

That media basket is a great way for them to sell more fleece

 

[aaron186]

Yeah, Steve over at [email protected] can help you out. I just order his rolls for my 5&12 Reefmat. However, his is a 2 inch vs the 1.5 (or whatever sizes they are) . He shared the contact with me of someone who was printing an adapter tube but he hasn’t replied to my emails. I haven’t tried it on the smaller tube.

I have been getting a month out of both my 1200 and my 500. However, the tank that has the 500 recently had a precipitation event, and is now going through rolls in less then a week. I’m likely going to have to take all the plumbing, UV, etc, off the tank and clean out the lines. There is a coating in all the plumbing that is now really causing me to go through some fleece. I’m going to give it one more roll to see if it cleans itself out… if you follow the dates, you can clearly see where the event took place… sigh…

Awesome thank you. I emailed him. Can you explain the adapter a little more? I’m a bit confused what you’re referring to

 

[musaabi]

That media basket is a great way for them to sell more fleece

Even a small amount of carbon causes it to raise the water level enough to run the Mat constantly

 

[Joj]

Awesome thank you. I emailed him. Can you explain the adapter a little more? I’m a bit confused what you’re referring to

Pm ‘mackdave’ hon here. He sells the 2” to 1.5” 3D printer roll reducer to use with the preconfilters. Basically the preconfilters are 2” diameter and the oem redsea filters are 1.5” only.

 

[mackdave]

Yeah, Steve over at [email protected] can help you out. I just order his rolls for my 5&12 Reefmat. However, his is a 2 inch vs the 1.5 (or whatever sizes they are) . He shared the contact with me of someone who was printing an adapter tube but he hasn’t replied to my emails. I haven’t tried it on the smaller tube.

I have been getting a month out of both my 1200 and my 500. However, the tank that has the 500 recently had a precipitation event, and is now going through rolls in less then a week. I’m likely going to have to take all the plumbing, UV, etc, off the tank and clean out the lines. There is a coating in all the plumbing that is now really causing me to go through some fleece. I’m going to give it one more roll to see if it cleans itself out… if you follow the dates, you can clearly see where the event took place… sigh…

Sorry but I make the adapters. I didn’t get your email. My email is [email protected] .

 

[aaron186]

Sorry but I make the adapters. I didn’t get your email. My email is [email protected] .

No you already did. I purchased from you. I emailed you a few months ago. I have been using your adapters for a couple months already