Sam's Oceanic 120 - DIY solutions

[Stang67]

Apex Fusion's "Measurements" section allows you to manually enter test results and trend the data.

Allergic to apex. I think it's the orange color
Personally not a fan of the "automation" idea at least not to that degree, plus tech and I don't get along too well.

 

[Projects with Sam]

Yes, Its Apex. The parameter part, if you don't have a trident is all manual.
You have to enter the data point by point as you do the tests....
the nice thing is that it does the conversion for you if you use Salifert.
so you don't need to reference the table to find out the value to type in.

 

[Projects with Sam]

omg. cannot believe it! so stoked! Didn't get a spin but I'll take it!
I stepped away to put my kid to sleep for awhile so I guess that is when I missed the IM being given out... that tank woulda been a sweet replacement for the 15 nem tank.

OBS Studio to get the recording.

 

[Projects with Sam]

Happy Thanksgiving all!
Heading home tomorrow! Hope the travel goes ok… at least it’s a direct flight.
sofar from my Wyze camera and Apex I don’t think I’ll have any surprises when I get home.

 

[Projects with Sam]

got in ok. things seem fine except that my Alk wen to 6.4... Kalk concentration seems fine... been adding alk slowly to get it back up.

 

[Projects with Sam]

 

[Projects with Sam]

Forgot to mention. I destroyed my MP10 dryside trying to change its bearings...
guess the nem tank will get less flow.

 

[rmorris_14]

dude... didn't you just get back from vacation?... slow down...

Also........ the mixing music . oh ok its total project music.

 

[tbrown]

dude... didn't you just get back from vacation?... slow down...

Also........ the mixing music . oh ok its total project music.

Come on, you have kids - define "vacation"

 

[Projects with Sam]

dude... didn't you just get back from vacation?... slow down...

Also........ the mixing music . oh ok its total project music.

hehe this is backlogged video from the spring! waaaay too cold now for polyurethane!

 

[Projects with Sam]

One-handed reload ParlaRoller:

I could sell DIY CNC kits; give away a few designs and how to videos and disrupt a fledgling sector.

 

[tbrown]

One-handed reload ParlaRoller:

I could sell DIY CNC kits; give away a few designs and how to videos and disrupt a fledgling sector.

Once I get mine dialed in I'm sure my wife's going to be asking for me to print her a CNC.

 

[Projects with Sam]

Once I get mine dialed in I'm sure my wife's going to be asking for me to print her a CNC.

This is a good one: https://www.thingiverse.com/thing:4645791
I'm making a new version of it that uses rails for the y-axis.

 

[Projects with Sam]

wow... how long till its available for people?!

 

[Projects with Sam]

Ive... just.... got... to.... (even though my cnc is too small)

 

[Projects with Sam]

hmm. think i just crashed r2r for a sec there...

 

[Projects with Sam]

 

[tbrown]

Mine is still having some issues. I found a good video from Ricky (the YouTube channel recommended by @stoney7713 ). I'ma check that out and make some adjustments later today if I have a chance (after I clean my hotend - failed print last night).

 

[stoney7713]

One-handed reload ParlaRoller:

I could sell DIY CNC kits; give away a few designs and how to videos and disrupt a fledgling sector.

Is this going to be an automatic roller or manual. I've thought about making a manual roller, just crank it a bit every morning or night. Should still be better than changing socks once a week.

 

[Projects with Sam]

Is this going to be an automatic roller or manual. I've thought about making a manual roller, just crank it a bit every morning or night. Should still be better than changing socks once a week.

automatic to replace my existing DIY roller:

much much more to come ;D