Sea Swirl installed with a wooden canopy

funguyatnight

New Member
View Badges
Joined
Jan 22, 2014
Messages
14
Reaction score
0
Location
Lafayette, LA
Rating - 0%
0   0   0
I wanted to share my installation of the Sea Swirl on a wooden canopy. Due to having the wooden canopy resting on the aquarium rim, I was unable to install the Sea Swirl the way instructed by the website www.sea-swirl.com. After ordering two units without a mounting bracket, I engineered the installation in the below pictures. The Sea Swirl units are very light and are supported by only a half inch PVC pipe. Take note that I drilled a hole in the back canopy and notched the door so when it swings open and close it does not hit the PVC pipe. Just be sure you measure and drill your holes correctly so the unit hovers over the tank at the same height as if it was mounted on top of the rim of the tank. Th units are silent with no vibration. The movement is slow and not distracting. This is new build so not sure how they will hold up but I will add to this thread with updates in time.
 

Attachments

  • IMG_3074.jpg
    IMG_3074.jpg
    93.5 KB · Views: 293
  • IMG_2992.jpg
    IMG_2992.jpg
    91.6 KB · Views: 282
  • IMG_2991.jpg
    IMG_2991.jpg
    94.4 KB · Views: 284
  • IMG_2990.jpg
    IMG_2990.jpg
    88.7 KB · Views: 287
That's pretty cool!
I've been looking at sea swirls lately.
It looks like yours is mounted at the front of the tank pointed towards the rear of the tank. Is this deliberate, or was it a result of having the canopy?
I've been wondering which would be better for the flow of the tank if both options were available.
 
I had two reasons to installing the Sea Swirls at the front of the tank.
1. I only have a 36" wide tank with a center overflow and I needed to fit two IM Vega LED lights in the back part of the canopy that covers 2/3 of the tank. I was worried that the center over flow would obstruct the full 90 degree sweep of the Sea Swirl.
2. This tank will be viewed from the front and the two sides, so I did not want any powerheads on the side of the tank. So I painted the back of the tank a very dark blue and place two small Vortech 10s on the back of the tank. This camouflages the powerheads nicely at the rear and with the Sea Swirl at the front I think I will no dead spots in my tank.
 
Very nice adaptation, GREAT JOB !

Cheers, Todd
 
Yes, they are in the front of the tank. I wanted to get water movement from the front and sides from the Sea Swirl and move me from the back from the Vortech 10s.
 
Props to a good DIY...

However how do you remove them for cleaning or repair if needed? It looks to me that there is no real way to get them out other than cut the pipe... Either that or there is just enough room to unscrew it and avoid the wood part of the canopy.
 
cdness,

You are correct. There is no easy disconnect. This may be my lack of experience on my part, but I a hoping since this is a high volume flow line and that the Sea Swirl is always moving, I am hoping I will not need to remove for cleaning often. If needed, PVC pipe is inexpensive if I need to cut pipe to remove.

Time will tell if this was a mistake.
 
I don't think it's a much mistake. I think it may just end up being a small pain in the distant future.
I had a pair of ( used when I got them) sea-swirls on my 240 for 5+ years before I had any sort of problem. The motor on one was giving out and the linkage on both needed a tuneup.

Just a quick cut with a hack saw and reinstall with a union, when needed.
 

IF YOU HAD TO TAKE A REEFING EXAM, WOULD YOU PASS?

  • Yes!

    Votes: 30 44.8%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 13.4%
  • No.

    Votes: 25 37.3%
  • Other (please explain).

    Votes: 3 4.5%
Back
Top