Tap water + CO2 = DI Resin destruction!! Advice needed

  • Thread starter Thread starter Phyber
  • Start date Start date
  • Tagged users None

Phyber

Active Member
View Badges
Joined
Aug 11, 2012
Messages
403
Reaction score
188
Location
Danville, VA
Rating - 0%
0   0   0
I live in the rural area and use a BRS 75gpd 4 stage RODI unit for my water.

I have always had problems with my DI resin exhausting far too early. I can get maybe 20g worth of water before its turned brown.

I asked BRS about CO2 killing the resin, and they really just advised to keep buying more :/ I know that it is common to have the gas in well water, and I always let my water sit for at least 3+ days before it goes into my tank in hopes of it de-gassing.

Coming in from the tap, my water is 35ppm TDS. After the RO it's at 4-5ppm TDS. When the resin is fresh, I get 0ppm TDS but once it's exhausted my finished water is whatever ppm comes out of the RO.

What can I do about this? Is my 5ppm reading something to really be worried about, or, is that the CO2 still I'm the water?

Unfortunately I do not have a handheld TDS meter to test e water after it has sat in my holding can.
 
I would check the membrane. I'm getting 240tds in and filters generally last 4-6 months running 0tds out. I do 10 gallons a week. I was told if the di goes quick then the membrane and other filters are shot.
 
I have the same issue. I use a degassing chamber after the RO and before the DI to remove as much co2 as possible. I have found that I get most of the co2 out after 24 hours of recirculating through the degassing chamber. To extend the DI even farther I added a second RO after the degassing with the reject from this one going back into the degassing system so I don't waste extra water. Spectrapure has plans somewhere on their site for a degassing setup. I expanded on that by making it recirculation as one pass didn't remove enough for me.

Looking at your numbers you have a very poor rejection rate, you might check pressure, pre filters or look into a new membrane as well
 
Last edited:
I would check the membrane. I'm getting 240tds in and filters generally last 4-6 months running 0tds out. I do 10 gallons a week. I was told if the di goes quick then the membrane and other filters are shot.
RO won't remove co2. Spectrapure also sells a test for co2 so you can see if that is your problem and how much degassing you will need to get it out.
 
I have the same issue. I use a degassing chamber after the RO and before the DI to remove as much co2 as possible. I have found that I get most of the co2 out after 24 hours of recirculating through the degassing chamber. To extend the DI even farther I added a second RO after the degassing with the reject from this one going back into the degassing system so I don't waste extra water. Spectrapure has plans somewhere on their site for a degassing setup. I expanded on that by making it recirculation as one pass didn't remove enough for me.

Thanks Rick. I had seen the same plans for a degassing chamber, and since I'm not a handy man, I was looking for an already made product or method that could solve this problem.

Let's say that I just let the DI stay dead, is there any harm in the 4-5ppm water I'm using for the tank? Are those ppm's the CO2?

Should I replace my RO membrane (which is roughly a calendar year old) or add the 150 upgrade from BRS?

Thanks!
 
The co2 wont show as tds. IMO 4-5 is high and will lead to a build up of nutrients. It's cheaper to pull it out with degassing and DI than GFO, I know from experience
 
The co2 wont show as tds. IMO 4-5 is high and will lead to a build up of nutrients. It's cheaper to pull it out with degassing and DI than GFO, I know from experience

:(

So I'm looking at a refill and a half of DI resin to fill my 32g brute holding can of 0tds water? The refills are ~$10 each...i run gfo 24/7 and a can of that is like $20...is it really cost effective for the refills?

Is there ANY other alternative?

Thanks!
 
I have the same problem with high CO2 from well water. Was only getting about 90 gallons of good water before i would exhaust the DI resin.

Here is how i fixed the problem...

First, dont throw away premature exhausted resin. Place in a large pan/bowl and keep moist, but allow it to air out. It will recharge itself if it was from high CO2 levels.

Second, on your RODI unit, remove the line going into your DI chamber and route that to a large container( i use a brute trash can) put a few stones in the container to remove the high CO2 levels. Allow 24hours to remove the CO2 out of the water. Using a maxijet pump or some other type, plumb it to to pump the DE-GAS water into your DI chamber.

I have been doing this for 6months and have made close to 1000 gallons of good water this way and still going strong on the same di resin.
 
I have the same problem with high CO2 from well water. Was only getting about 90 gallons of good water before i would exhaust the DI resin.

Here is how i fixed the problem...

First, dont throw away premature exhausted resin. Place in a large pan/bowl and keep moist, but allow it to air out. It will recharge itself if it was from high CO2 levels.

Second, on your RODI unit, remove the line going into your DI chamber and route that to a large container( i use a brute trash can) put a few stones in the container to remove the high CO2 levels. Allow 24hours to remove the CO2 out of the water. Using a maxijet pump or some other type, plumb it to to pump the DE-GAS water into your DI chamber.

I have been doing this for 6months and have made close to 1000 gallons of good water this way and still going strong on the same di resin.

I will try the "self regeneration" tonight and see what happens.

I'd really love to do a degassing tower or etc, however, size is my problem...I would love to have it so that in one swoop I am running the water through the rodi unit as well as the degassing tower then into my bucket. I don't have the space for multiple brute cans, nor the patience to go back to making RO water one 5g bucket at a time.
 
Why don't you recharge your DI resin I do haven't bought any in 2 years I get 0 tds

I've read the steps, and while I feel I could successfully regenerate the resin, the time and process is a bit over the top unless other methods have come along.
 

IF YOU HAD TO TAKE A REEFING EXAM, WOULD YOU PASS?

  • Yes!

    Votes: 30 44.8%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 13.4%
  • No.

    Votes: 25 37.3%
  • Other (please explain).

    Votes: 3 4.5%
Back
Top