Tunze 3155 ATO not stopping till it hits emergency float

Ducksalt

New Member
View Badges
Joined
Mar 10, 2019
Messages
7
Reaction score
4
What state or country do you live in
California
Rating - 0%
0   0   0
Today I received my Tunze ATO and was exceited to set it up so now I dont have to fill by hand and keep a steady water level for my skimmer. It seemed to be working fine and turned on for about 10 or so seconds and shut itself off. The optical eye/float is installed in the return pump chamber of my Nuvo 40. About 10min after it kicked on the first time I heard it start pumping again but this time didn't stop. The "Pump On" light was lit yellow but the "Low Level" or "High Level" were not on. The water level completely submerged the optical eye and didn't stop till the emergency float was activated and the alarm kicked on. Is this a fault sensor? I tried unplugging and plugging back in but it just powers on and keeps pumping if the water is not pushing the float up even though the eye is submerged.
 
Sounds like a faulty eye.

Also double check that you aren't siphoning out of the ato container. Make sure your discharge is above the water level of the ato container.
 
Sounds like a faulty eye.

Also double check that you aren't siphoning out of the ato container. Make sure your discharge is above the water level of the ato container.
Reservoir is below tank and the discharge hose is not in the water. It is being held in the bracket and attached to the back of the tank 2-3 inches above the water.
 
Screenshot_20190404-231909_Chrome.jpg
 
Ok, I'll take some water out of the tank because it is already above the baffles now and move it out of the water and power it back on. The only thing is why did it fail in the first place. If I would have let it go on its own it would have hit the emergency float shut off. I also just lowered the dial on the inside of the controller to nano so it will fill more slowly. Maybe it filled to fast and threw the sensor off?
 
If the eye is submerged, it will never find it and keep pumping.

That’s not true, you may have had a faulty unit. When powering on the Tunze 3155, it always cuts on the pump for about 10-15 seconds, regardless of the water level, I believe just to prime the line (it’s assuming it’s being setup for its first use). My eye is always already submerged, but that doesn’t affect the initial prime when powering it back on. After that prime, if the eye is submerged, it shouldn’t come back on until it needs to bring the water level back up. If it keeps pumping non-stop, beyond that initial prime, even though the eye is submerged, then you may have a faulty unit or need to clean the eye.
 
Ya, the eye is brand new and not dirty at all, but I did pull it and wipe it just in case. I actually plugged the unit back in and just held the tube so it was go back into the reservoir and not put water in my tank and it just ran and ran for a couple min. There are no lights on for water level high or low, just pump on.
 
Oh maybe @rvitko can help me out then. Thanks. I did send help email directly through the Tunze site too.
 
My 3155 does the same thing when started back up. It will fill right past the optical eye and trip the float/alarm. Ive just learned to deal with it, ill take out a turkey basters worth of water when this happens and it works fine until shut off again. Not sure if its an issue w the eye or not, but does not seem to be a flood risk as the float always does its job. Tunze has been great w replacing a faulty pump issue so Im not going to bother them w this. If
 
Ya, the eye is brand new and not dirty at all, but I did pull it and wipe it just in case. I actually plugged the unit back in and just held the tube so it was go back into the reservoir and not put water in my tank and it just ran and ran for a couple min. There are no lights on for water level high or low, just pump on.

Yeah that sounds faulty, like it’s not reading the optical sensor at all. If you completely submerge the optical sensor, and then turn it on, does the pump not cut off after about 15 seconds or so? If not, then that definitely seems faulty or maybe not connected to the controller. Is there anything else magnetic near the sensor (other than the magnet used to hold the sensor mount)? One time my 3155 went haywire when I mounted my dosing line holder right next to the sensor mount because the additional magnet was throwing it off somehow.
 
That’s not true, you may have had a faulty unit. When powering on the Tunze 3155, it always cuts on the pump for about 10-15 seconds, regardless of the water level, I believe just to prime the line (it’s assuming it’s being setup for its first use). My eye is always already submerged, but that doesn’t affect the initial prime when powering it back on. After that prime, if the eye is submerged, it shouldn’t come back on until it needs to bring the water level back up. If it keeps pumping non-stop, beyond that initial prime, even though the eye is submerged, then you may have a faulty unit or need to clean the eye.
+1 to this. Mine is also submerged as I’m normally doing a water change with pumps off when I turn the Tunze off, and the eye is submerged when I turn it back on.

You could try cleaning any film from the eye, as if it’s new they sometimes have a fine film on them (I read this somewhere!)
 
Nevermind. I just saw that you said the pump doesn’t turn off.
 
Thank you all for the reply's. If I start from scratch, have the sensor just above the water level and plug it in the pump will pump for its 15 seconds then stop as it should. After that it may work one more time but then it will kick itself back on and not stop till it hits the float switch fail safe. Its like the sensor sometimes works and sometimes doesn't.

I added some pics, as you can see the reservoir is below the tank and the tube is not in the water to prevent siphoning. The water will rise and completely cover the optical eye and not stop.

https://imgur.com/YMjfaaK
https://imgur.com/auayAjr
https://imgur.com/8DP2SzK
 

IF YOU HAD TO TAKE A REEFING EXAM, WOULD YOU PASS?

  • Yes!

    Votes: 30 44.8%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 13.4%
  • No.

    Votes: 25 37.3%
  • Other (please explain).

    Votes: 3 4.5%
Back
Top