what determines the size of a centre brace

mikesuperrc

New Member
View Badges
Joined
Jan 5, 2018
Messages
12
Reaction score
1
Rating - 0%
0   0   0
Hi
I'm just trying to work out what determines the size of a center brace.

I have a 4x2x2(120x60x60cm) aquarium that I'm resealing and have removed the top braces to reseal they will be going back on.

It has braces around the sides, front and back that are about 2inch(50mm) wide but don't go right to the edges they finish about 10mm from the corners and the side braces about 10mm from the front and back brace.

It currently has a 8 inch (200mm) wide centre brace.
All glass aquarium and braces are 3/8" (10mm)

And I am wanting to replace it with a stainless steel brace that is made up properly so that it can be narrower so as not to affect light so much and look nicer. As am considering an open top, no lids.

So I'm trying to figure out what determines the width of a center brace so I can figure out what size steel I need use.
I am thinking of brace along the lines of the one pictured
Thanks[emoji16]
97106b227d3be33cc36289e160c08c04.jpg
1e57b13940e8937e0c69bb008aeda44f.jpg
7aab8cb6fe17578b76a117bfe96f58a1.jpg
 
Why not use glass as a center brace? Won't cast as bad shadows as steel (or plastic) and won't potentially drip rust/metal particles down into the water.
 
Why not use glass as a center brace? Won't cast as bad shadows as steel (or plastic) and won't potentially drip rust/metal particles down into the water.
If I went the steel brace it was probably going to be one in the middle.

I am thinking a piece of 10x10mm bar if that is adequate instead of the two smaller rods.
so would be able to fit larger Rocks etc in the tank and easier to clean.

At the moment I have a freshwater 4x2x2 set up pretty much the same way, with the 200mm wide centre brace, and I'm always cleaning the watermarks, etc. off of under it otherwise it blocks out light anyway

If I went the stainless steel it'd be 316grade and probably an epoxy clear or some coating on it so rust, etc. wouldn't be an issue.

Do I need to have it 200mm wide this width so that there is enough purchase for the silicone or is it for the strength of the brace.
 
With those front and back braces you have installed, I don't think you need the center brace at all. They will do much more than the center brace to prevent bowing. It does not matter that they do not go all the way to the corners. The only issue is that they do not have much resistance to vertical weight or lifting because they are not sealed in the corners.
 
Last edited:
With those front and back braces you have installed, I don't think you need the center brace at all. They will do much more than the center brace to prevent bowing. It does not matter that they do not go all the way to the corners
Is it the glass ones you are referring to?
 
Yes, the ones in the first picture. If those are at the top of the tank it should be well braced.
 
Even though it's only 10 mm glass?
I've been told it needs to be at least 12mm to do without the centre brace
 
I don't have any calculations to support it but I find it hard to believe that a 2" wide 3/8" thick brace is not going to be strong enough. I have seen plenty of 3/8" center braces on older tanks. If you are really concerned I would replace them with 10 mm going all the way to the corners over the metal center brace.
 
I don't have any calculations to support it but I find it hard to believe that a 2" wide 3/8" thick brace is not going to be strong enough. I have seen plenty of 3/8" center braces on older tanks. If you are really concerned I would replace them with 10 mm going all the way to the corners over the metal center brace.
OK cool I do like the idea of no Center brace at all. just don't want the tank bursting.

If it was going to cause issues without a centre brace would you notice the bulge straight away when filling it up or would it be something that happens over time
 
I think what they meant was that you need 12 mm for no brace at all. Just to be clear, I am talking about a so-called euro brace with a full silicon seam between the brace and the front and back panels. The front panel would flex quite a bit before it actually broke as you were filling it if it were not adequately braced. As long as the brace does not break or become separated from the panel, it should not flex.
 
I think what they meant was that you need 12 mm for no brace at all. Just to be clear, I am talking about a so-called euro brace with a full silicon seam between the brace and the front and back panels. The front panel would flex quite a bit before it actually broke as you were filling it if it were not adequately braced. As long as the brace does not break or become separated from the panel, it should not flex.
Ok cool i might look at getting some longer bits of glass and doing it that way would having a small piece of glass under the joints of the brace help it also
 
Like a backing for the join. say a piece 50 mm wide and 100 mm long siliconed to the bottom or top side of join in the braces
 
You can do that or you can just silicon the front and back braces to the side braces but they would have to be longer than they currently are (i.e. replaced). The long front and back braces should be somehow supported on the ends with silicon to the side braces or side panels.
 
Ok i give that a go would having the braces 3mm shorter then the internal dimensions of the tank be adequate or is there somewhere I can find this information I am guessing there has to be room for the silicon
 

IF YOU HAD TO TAKE A REEFING EXAM, WOULD YOU PASS?

  • Yes!

    Votes: 30 44.8%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 13.4%
  • No.

    Votes: 25 37.3%
  • Other (please explain).

    Votes: 3 4.5%
Back
Top