WHATS WRONG WITH MY PARAMETERS
Troylee
all about the diy!!!!!
Alk is high , salinity is a touch low and your nitrate is low. Depending on what salt you use a water change may correct them. Nitrates you need to feed your fish more, add more fish or start dosing nitrate.
Nate Chalk
7500 Club Member
What.
OPL
Community Member
Devisissy
Kiss My Wrasse
Well I have an old retired police dog. He walks the perimeter all day long. I think his bark is worse than his bite but Johnson doesn't know that and he hasn't tried to steal from the scrap pile since I got cujo.
Now if you are talking about parameters something just ain't adding up. How can salt and ph read that low with alk that high? What test kit are you using, salt brand, how are you mixing said salt? Then maybe we can figure this out.
Now if you are talking about parameters something just ain't adding up. How can salt and ph read that low with alk that high? What test kit are you using, salt brand, how are you mixing said salt? Then maybe we can figure this out.
Cycleguy0623
Active Member
- Joined
- Dec 18, 2015
- Messages
- 198
- Reaction score
- 178
I agree with the above, something is not adding up. Test kit type and salt mix used could help figure it out. I would retest all parameters and go from there.
Devisissy
Kiss My Wrasse
Take that api and throw it in the trash.
ekandler
Active Member
My thoughts:
- alk is really high. Should be 7.5-8.5dkh
- phosphate and nitrate is out of balance. Phosphate at 0.15ppm is okay but nitrate at 0ppm is too low. Your corals are starving and possibly being burned by the phosphate level. Look up Redfield ratio.
- stop testing nitrite. If your cycle is complete, it’ll stay 0.
- stop paying attention to pH. pH has to be way way off to cause any harm. Tuning pH is a more experienced reefing thing, so forget that for now.
- Salinity is too low and you should keep it consistent. Corals don’t like fluctuations in salinity.
ekandler
Active Member
Realistically, you have no idea what your values are because API test kits are terrible. Before spending any money on corals, spend money on good test kits. Start with a good foundation and you’ll be set. Inconsistency in testing results is going to kill your corals and waste you money.
Mr. Mojo Rising
7500 Club Member
I would not make any changes to the tank based on API results, better to buy quality test kits.
Why do you assume something wrong with your parameters? Can we see a tank pic? A tank can adjust to parameters, so how a tank looks is more important that actual numbers
Why do you assume something wrong with your parameters? Can we see a tank pic? A tank can adjust to parameters, so how a tank looks is more important that actual numbers
Cycleguy0623
Active Member
- Joined
- Dec 18, 2015
- Messages
- 198
- Reaction score
- 178
Instant ocean typically mixes up around 10dkh I believe. Water changes will not lower that if you’re using the same salt mix. Corals will consume it but if you have no corals it will not come down that fast.
As others have said toss the API there not know for consistency in testing. Also salinity is to low and fee more to get nitrates up. I run nitrates at 3-5 consistently. I would go higher but I would need to dose them specifically. Today’s equipment and media can filter a tank empty of nutrients.
It may be time to change salt mix to keep that dKH in check without a lot of coral growth.
As others have said toss the API there not know for consistency in testing. Also salinity is to low and fee more to get nitrates up. I run nitrates at 3-5 consistently. I would go higher but I would need to dose them specifically. Today’s equipment and media can filter a tank empty of nutrients.
It may be time to change salt mix to keep that dKH in check without a lot of coral growth.
jabberwock
2500 Club Member
The big problem with API tests is user error and subjective color determinations. The kits are fine, the users are typically the variable. Follow the tests to the letter, measure carefully, remeasure if you get strange results. Ask someone else to judge the colors. We all see color differently.
API alk test is perfectly fine. It is a titration, like all good alk kits. It is easy to use and matches my Salifert. It is only read in increments of 1, but you can double your sample volume to make it +/- 0.5 dKH.
Devisissy
Kiss My Wrasse
It's really not. All the way down to the test tubes. They give way to much margin of error for the average hobbyist.
Tell me about your problem with the test tubes.
