72x30x18 DIY build thread

[Mschmidt]

I've got a bunch of these waiting to get used.

 

[Nate Chalk]

I've got a bunch of these waiting to get used.

Now that with the clip in for the 80/20 channel would be perfect.

 

[Mschmidt]

Now that with the clip in for the 80/20 channel would be perfect.

I'm sure @Projects with Sam could draw it in a minute. It'd take me a week.

 

[Nate Chalk]

I'm sure @Projects with Sam could draw it in a minute. It'd take me a week.

Uhh ... And then how do I get it printed! I'm so in

 

[Mschmidt]

Uhh ... And then how do I get it printed! I'm so in

I would if I don't need to figure out the drawing. I'm sure one of the cronies could too.

 

[Nate Chalk]

I would if I don't need to figure out the drawing. I'm sure one of the cronies could too.

Seriously y'all have 3d printers?!

I would love that.

The cable situation is awful wanna see

 

[Mschmidt]

Seriously y'all have 3d printers?!

I would love that.

The cable situation is awful wanna see

I'm down for some bad cable management pics.

 

[Projects with Sam]

I'm sure @Projects with Sam could draw it in a minute. It'd take me a week.

When I get back I’ll make one and put it on thingiverse. Will also sell packs of 10.
I just need to remember when I get back!

 

[Nate Chalk]

When I get back I’ll make one and put it on thingiverse. Will also sell packs of 10.
I just need to remember when I get back!

I'll reach out that sounds awesome .

@Mschmidt all at one point zip tied to the only 3 pts of contact I have ATM lol those clips will make it much easier and tighter

 

[Nate Chalk]

Skimmer height being up another inch or 2 is making it suck air from the front. Mini cyclone kicks up and it sucks air.

Gonna be tweaking this thing

 

[Projects with Sam]

I suppose you could get a high walled tupperware and inset it in the sand and put the skimmer in lower or just raise sump level.

 

[Nate Chalk]

I suppose you could get a high walled tupperware and inset it in the sand and put the skimmer in lower or just raise sump level.

Yeah working towards that. The 3d printed piece roughly how much per you thinking? I'll need 30 probably

 

[Projects with Sam]

i‘ll match the McMaster-car unit cost you sent; I suppose.

 

[Nate Chalk]

i‘ll match the McMaster-car unit cost you sent; I suppose.

:O

Sounds like a good idea. 80/20 cable management clips sound sweet.

 

[Mschmidt]

I'll reach out that sounds awesome .

@Mschmidt all at one point zip tied to the only 3 pts of contact I have ATM lol those clips will make it much easier and tighter

At least there is an attempt. unlike me. I'll be adding the ones I made to the stand to help guide them too.

@Projects with Sam I got the one I posted from thingiverse I printed 30 at a time and had one, maybe two failures.

 

[Goaway]

 

[Nate Chalk]

Which #Cronies has the oxydator?!

I just got a size D for Christmas!

Dunno if it's big enough to effect 250gallons based on the calculation. Any feedback on yours would be great

 

[danieyella]

Which #Cronies has the oxydator?!

I just got a size D for Christmas!

Dunno if it's big enough to effect 250gallons based on the calculation. Any feedback on yours would be great

That'd be me, maybe someone else as well.

Definitely makes a difference but I believe you're undersized.

 

[Nate Chalk]

That'd be me, maybe someone else as well.

Definitely makes a difference but I believe you're undersized.

I thought so : err... Need a W or A with 2 catalyst

Wondering if it helps at all being undersized found a chart with the break downs

 

[danieyella]

I thought so : err... Need a W or A with 2 catalyst

Wondering if it helps at all being undersized found a chart with the break downs

@Lasse can you contribute?