A way to Fill up Entire Tank

YEGReef

Community Member
View Badges
Joined
May 18, 2019
Messages
26
Reaction score
17
What state or country do you live in
Canada
Rating - 0%
0   0   0
Silly question but is there any way I can have my tank filled to the rim.
When I used to use Canister filters it wasn't an issue.

This tank (I've attached a picture) the 2 return lines on each end are slightly lower than the overflow box.
So currently with the tank filled and the sump at the proper operating level, the water line is at the overflow box.

Is there anything I can adjust to raise the water level to the rim, I am not a fan of seeing the waterline and missing those few inches from the top annoys me.
Do I reduce the drain flow, or increase the pump speed?

Thank you!

W2PuwDz.jpg
 
Firstly, very interesting tank you have there. I sure like the look!
Secondly, I am following this as I am not sure how you would increase the water level based on this design. I am very curious to see what others have to say though.
 
I'm not certain I would recommend it, but one way would be to insert standing pipes into your overflow box. The water won't drain out the bottom of the overflow, it will rise to the level of the pipe stuck into the bulkhead in the overflow. You determine the level by the length of the pipe.

 
Careful how high you go till you determine your tank flow. By the time you get your power heads running right you may have water on the floor if you go too high. I shoot for an inch of movement minimum with a 1/2" of safety net. That being said both of your thoughts are correct upping the pump or limiting the drain line will indeed raise the water level. Cool looking tank brother!
 
You could increase the return pump flow or add a solid or mesh plate to the lower portion of the weir. I’m not necessarily recommending either of these options, just trying to answer your question on how to accomplish it. Good luck!
 
Personally I would get some clear acrylic and silicone it to the inside of the weir on your overflow at whichever height you want. This gives you the advantage of not messing with the flow through your drain or the sump. Be sure to use the correct silicone if you do though
 
Personally I would get some clear acrylic and silicone it to the inside of the weir on your overflow at whichever height you want. This gives you the advantage of not messing with the flow through your drain or the sump. Be sure to use the correct silicone if you do though

@JoshH - I’m tracking with you and the one tweak that I would make is to make it adjustable (at least at first).

What I have done in the past is to use either plastic mesh or a reef safe plastic/ acrylic, add holes at the appropriate spots and then put zip ties through the holes creating loops that will slide over a couple of the weir fingers. The down side is that the more of the weir that is blocked then the higher the risk of an overflow. Good luck!
 
@JoshH - I’m tracking with you and the one tweak that I would make is to make it adjustable (at least at first).

What I have done in the past is to use either plastic mesh or a reef safe plastic/ acrylic, add holes at the appropriate spots and then put zip ties through the holes creating loops that will slide over a couple of the weir fingers. The down side is that the more of the weir that is blocked then the higher the risk of an overflow. Good luck!

I'm much more impulsive I'd just glue it too high and if I needed to make any adjustments downwards, get a drill bit the same size as the slots in the weir and grind them down.

Zip ties would be a nice easy way To make adjustments :)
 
I'm not certain I would recommend it, but one way would be to insert standing pipes into your overflow box. The water won't drain out the bottom of the overflow, it will rise to the level of the pipe stuck into the bulkhead in the overflow. You determine the level by the length of the pipe.

+1
Also that is a sweet looking setup!!! got a build thread?
 
That's a google image.. lol. I do have something similar ging on, but it's the nasty white pipe and looks rather unfabulous :(
haha, but like William posted the drain pipes determine the water level. Here's a pic of the back of my tank and you can clearly see my returns are lower then the overflow box.
tank back.jpg
 
Now that I'm really thinking about it, I would make it a priority to install a primary drain stand pipe and an emergency drain stand pipe that sits at the max height you're comfortable with. Tuning your drain with a gate valve, or even adjusting the flow on your return pump is a dicey solution.

It will almost always fall out of balance. If your return pump gets a little dirty and clogged and slows down (probably the most common scenario) the overlflow will empty out and you'll get a sucking sound. No big deal. However, if it is your drain line that slows down bc of algae, snail, whatever, the display tank will overflow all over your house.

That can happen because you're using the full capacity of your primary and emergency drain bc they're both in full use at the bottom of your overflow. You need to make it so the emergency drain is barely used.. like a trickle. It holds the level where you want it, but if the primary drain clogs, it still has enough draining capacity in reserve to noisily drain your tank until you notice the problem.
 
If that's not your exact set up then order a exotic marine systems or modular marine overflow and run a bean animal overflow. problem solved.
bean.jpg
 
Increased water height = higher chance of carpet surfers, looking at those euro braces at the end i bet you'll have fish on them if the water is right to the top.

Personally i wouldn't worry about the volume loss but i would fit some thin acrylic fascias the same colour as the cabinet just around the top rim, say 1" deep to cover the water mark.

If you're smart the bottom of the fascias are JUST below the water line and if your return pump is off then you'll be able to see the water line ie from 10ft away you'll know if your return pump is running or not, a nice safety feature.
 
Hey,

Lots of good advice. Only thing I may mention is if your raising the water level in the overflows obviously you are reducing the length of the teeth in the weir. If the water line gets to high it may be easier for a fish to get in the overflow. Also if you block some of the weir teeth you will have to reduce flow for it to keep up or it will wind up going over the weir teeth

Just some thoughts. The manufacturer probably put it at that height for a reason. Also if the return lines are set to match the overflow box it is meant to break the siphon when it drains to a certain point.

Doesn’t mean it can’t be modded. Just test it out first. Hope I made sense.
 
Thank you all for the responses, very very helpful. Probably should have mentioned I am using the Herbie method so I probably can't play around with the water level by closing valves or it'll affect the method. But putting a piece of glass or acrylic behind the weir teeth may end up working, brilliant idea, I'm going to play around with it this weekend.

The family says it doesn't look too bad but I think its a bit too much, 2nd picture shows the amount.

GKq09qU.jpg

MubSfMW.jpg
 
I deliberately lowered the water line on my last build so I could crank up the surface agitation and get some awesome looking waves going with the Vortechs. As mentioned above, the more you cover the teeth on your weir the less effective the overflow is working with its job of surface skimming. The bottom of the teeth are designed to maximise flow and minimise noise. At the very least you want some of the teeth exposed
 

IF YOU HAD TO TAKE A REEFING EXAM, WOULD YOU PASS?

  • Yes!

    Votes: 30 44.8%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 13.4%
  • No.

    Votes: 25 37.3%
  • Other (please explain).

    Votes: 3 4.5%
Back
Top