Digital Aquatics Archon
- Thread starter EuroDriver
- Start date
- Tagged users None
n2585722
2500 Club Member
Mine happens to be double the ramp time also. Just make sure it isn't close to 24hrs total. The off time has to be more than the ramp but not necessarily double. Just make sure and leave several hours of time that the timer is not active. If you power down or reset your timers will get out of wack and the more inactive time the more quickly they will correct themselves.
n2585722
2500 Club Member
It has been a long time since I used the ALC. I though the white and blue had seperate timers. You can use the same timer but you have to assign it to each. The timer looks OK. If you need to change it the best bet is to erase it and setup another timer. They do not like to be changed . Especially if you change it while it is still active.
Ok thanks Danny. I’ve not had to run a separate timer for both blue and white channels. One timer worked both. I’ll clear it out after I know it is supposed to be off and start a new one. We’ll see how long that one lasts.
This morning I was greeted with an alarm from my Archon saying the vodka dosing container needed to be refilled. Turns out the DP1 I am using to dose vodka to my nitrate reactor dumped half the container into the reactor before the low level float shut it down. This is ridiculous. Why does this controller ignore programming? And why isn't there a viable help service available through DA? My help tickets go unanswered.
BTW the light timer was changed last night and they still came on at the wrong time this morning. Danny I did see where you said the timer needs to be added to both the blue and white channels which I didn't do. I'll change that and see what happens but I never did that before when the Archon was working properly.
Are there other ways to contact DA where you can actually get help? Sorry for venting but the livestock in these tanks is too much money to have it ruined by unreliable equipment.
BTW the light timer was changed last night and they still came on at the wrong time this morning. Danny I did see where you said the timer needs to be added to both the blue and white channels which I didn't do. I'll change that and see what happens but I never did that before when the Archon was working properly.
Are there other ways to contact DA where you can actually get help? Sorry for venting but the livestock in these tanks is too much money to have it ruined by unreliable equipment.
n2585722
2500 Club Member
Sorry I didn't reply any faster. I had an issue with my fridge last night. At this pimt you may want to try and shutdown the controller pull the memory stick and copy it to a folder on your computer. Make a new folder to do this. Then check the memory stick with the computer for errors. Fix them if any are found. Re install the memory stick and power the controller back up.
EuroDriver
Active Member
Need a little help here - I have lost WiFi connectivity on my Archon via my home WAN.
I have reset the Archon 3 times and repaired the USB (it did have erros). Upon reset, I can connect via the Archon hotspot. After I reconfigure the hotspot connection to my WAN, it will connect once, then lose connection again and I can't re-establish the connection until I do another reset.
Upon reconfiguring, it always connects via the same ip address, since I have reserved it on my router.
Any ideas?
I have reset the Archon 3 times and repaired the USB (it did have erros). Upon reset, I can connect via the Archon hotspot. After I reconfigure the hotspot connection to my WAN, it will connect once, then lose connection again and I can't re-establish the connection until I do another reset.
Upon reconfiguring, it always connects via the same ip address, since I have reserved it on my router.
Any ideas?
n2585722
2500 Club Member
Did you save the files on the memory stick prior to this happening. If you did you can try copying these files to a different memory stick and power up the Archon with this memory stick. Make sure the copy was vefore you had an issue and use a different memory stick.
Bigzman
Community Member
Seems that way sadly. It has great potential still. Hardware is strong but software side is not getting the attention it needs. With GHL and apex stepping up their software and support, not sure what’s going to happen to digital aquatics. I hope I am wrong.
I'm somewhat surprised that they even released Archon. From a software interface perspective it is IMO not even ready for the JV team, not even close to what a consumer should expect from a paid for user GUI. MyReef has never really worked for all Windows 10 computers and they really should have outsourced that to someone competent to get it done. Their hardware has always been rock solid though ( minus the iffy salinity probe and constant re-calibration ). They really should just open source the I2C protocol they use and let the community build applications for it, will probably keep them more relevant longer especially with the DIY crowd. At this point I have an APEX on my larger tank and figured I would try DA on my nano since it needs less optimization, but since they can't figure out MyReef and there is no way I'm paying that kind of money for Archon, I'll probably switch this tank over to another APEX unit.
pickupman66
5000 Club Member
Yes. DA has been shelved by Dynon completely at Thai time.
Jeepguy242
Valuable Member
Sad.
I can’t even get someone to approve my joining of the digital aquatics support forum and get my account activated
I can’t even get someone to approve my joining of the digital aquatics support forum and get my account activated
Jeepguy242
Valuable Member
I know this. The community here is awesome and I am sure that any question that I may have would be answered here
The problem is there are a lot of extra instruction sheets that digital aquatics has posted on the forum with “tips and tricks” that apply to most of my modules that I cannot even view by not having an activated account. I would like to have a look at these to see if they might help me with programming or any issue I might be able to work out before I need to ask a question
n2585722
2500 Club Member
The webpages were done in java script. If you know that language then you can change things to your liking. I would be carefull doing that though.
