ESHOPPS Mariner 70 Build

[tbrown]

FTS with the new lid!

 

[nickng]

FTS with the new lid!

Wonder what’s the overall height of the tank?

 

[tbrown]

Wonder what’s the overall height of the tank?

From the floor to the top rim of the tank is right at 57.5" I believe. I can measure again when I get home this afternoon.

 

[tbrown]

The shelf next to it is 72".

 

[SFBB-ON]

Do you have and photos inside the stand on the right side? I’m trying to decided how to go about the electronic side of the tank, and where to put everything.

 

[SFBB-ON]

Do you have and photos inside the stand on the right side? I’m trying to decided how to go about the electronic side of the tank, and where to put everything.

I don't know why this posted this message again lol...

 

[tbrown]

Do you have and photos inside the stand on the right side? I’m trying to decided how to go about the electronic side of the tank, and where to put everything.

I put a small screw in the back and hung one of the power strips. The other one takes different screws for mounting so it's sitting on the ground. My wiring is a mess so forgive me.

I'll eventually mount the other power strip just below the hanging one.

The heater controller is going to likely be mounted to the door just below the power strips.

ATO reservoir didn't fit in the right hand side so it's on the bottom shelf of the shelf next to the tank. I'll be printing a hanger that will hold both the heater controller and the light controller.

I'll also likely have the doser and the dosing reservoirs on the shelf outside the stand OR I'll mount them to the door on the left side - I haven't decided yet.

 

[tbrown]

Also, I'll point out that the wires aren't the permanent wires which is partially why they're a mess still - I haven't taken the time to clean up what I'll be changing soon. I have a few things that are temporary until I transfer from the other tank.

 

[Projects with Sam]

I put a small screw in the back and hung one of the power strips. The other one takes different screws for mounting so it's sitting on the ground. My wiring is a mess so forgive me.

I'll eventually mount the other power strip just below the hanging one.

The heater controller is going to likely be mounted to the door just below the power strips.

ATO reservoir didn't fit in the right hand side so it's on the bottom shelf of the shelf next to the tank. I'll be printing a hanger that will hold both the heater controller and the light controller.

I'll also likely have the doser and the dosing reservoirs on the shelf outside the stand OR I'll mount them to the door on the left side - I haven't decided yet.

wow that looks like it might be a great spot to add some slides:

Mastercraft® 22" Cadmium Full-Extension Ball-Bearing Soft-Close Drawer Slide

Update your cabinetry with the stylish looks of Mastercraft cabinet hardware. With trendy designs that are sure to fit your needs.

www.menards.com

and put a control board that just tucks right in there...

 

[tbrown]

wow that looks like it might be a great spot to add some slides:

Mastercraft® 22" Cadmium Full-Extension Ball-Bearing Soft-Close Drawer Slide

Update your cabinetry with the stylish looks of Mastercraft cabinet hardware. With trendy designs that are sure to fit your needs.

www.menards.com

and put a control board that just tucks right in there...

That area is just so skinny that drilling is almost impossible. I needed to do that before the stand was built.

 

[Stang67]

That area is just so skinny that drilling is almost impossible. I needed to do that before the stand was built.

They make drill elbows?

 

[ESABOE]

FTS with the new lid!

That lid is perfect! Subtle, doesn’t take away from DT

 

[tbrown]

They make drill elbows?

They make those 90 degree drills I think. I'm not overly worried about it.

 

[tbrown]

I've actually considered building a fake back wall to hide the wires. I think I could do that fairly easily and just drill a couple of holes that the wire ends could slip through. All the excess wire would be hidden behind that. I would probably also attach some LED backlighting behind it and on the front lip to help give a little more light inside when the door is open. Not sure if I'd put it on a controlled outlet or just wire a door switch - door switch would be better, controlled outlet would be easier.

 

[907_Reefer]

They make drill elbows?

I have one of these, has come in handy on more than a few occasions..

DEWALT MAXFIT Right Angle Magnetic Attachment DWARA60 - The Home Depot

The DEWALT MAXFIT Right Angle Attachment features a compact 1-1/2 in. front-to-back design. This Right angle holder provide users with accessibility in close-quarter drilling and fastening applications.

www.homedepot.com

 

[tbrown]

ATO pump and LiveAquaria stuff should be here this evening! Unfortunately, I shouldn't be here this evening... Everything is shelf stable so it won't be a big deal and my mother-in-law is likely going to be spending the night at our house tonight to watch the dogs so the boxes won't be sitting on the porch.

Goodies when I get home tomorrow or Saturday!!!

 

[ESABOE]

ATO pump and LiveAquaria stuff should be here this evening! Unfortunately, I shouldn't be here this evening... Everything is shelf stable so it won't be a big deal and my mother-in-law is likely going to be spending the night at our house tonight to watch the dogs so the boxes won't be sitting on the porch.

Goodies when I get home tomorrow or Saturday!!!

Going somewhere fun?

 

[tbrown]

Going somewhere fun?

Probably going to head up north to see a little snow.

 

[ESABOE]

Probably going to head up north to see a little snow.

Nice! Enjoy the time away with the fam!

 

[Fishy Guy]

Following!