How to install RODI on this faucet?

[Jmunk]

Installing the new RODI for the new tank in this house. How do you guys suggest I install it to these faucets, is it possible? I got the BRS adapter kit too but obviously none of the adapters work on these either. I'm thinking about just tapping in directly into the sink, but BRS's kit for that is sold out. Anyone have any Home Depot or Lowes links that you're using that work?

 

[Jekyl]

Won't work on that faucet. Laundry hook ups are best, or install a new fitting to the pipes leading to that faucet underneath

 

[mdb_talon]

Are you sure that aerator does not screw out? Almost all faucets have replaceable aerators...even the fancy looking ones.

 

[Soren]

Are you sure that aerator does not screw out? Almost all faucets have replaceable aerators...even the fancy looking ones.

I wonder the same. If the aerator is removable, an adapter may be needed, but that is much easier and cheaper than adding a splitter under the cabinet to have a second tap.

 

[Jmunk]

Won't work on that faucet. Laundry hook ups are best, or install a new fitting to the pipes leading to that faucet underneath

Figured, have a link to a good one? BRS is sold out of theirs.

 

[Jmunk]

Are you sure that aerator does not screw out? Almost all faucets have replaceable aerators...even the fancy looking ones.

Almost positive. There's literally nothing to grab to even screw it out. It's completely seamless as far as I can tell.

 

[Jekyl]

Figured, have a link to a good one? BRS is sold out of theirs.

Fitting is easily installable. Trying to attach to the pipe underneath the sink? Go to home depot. Get a 1/2"x1/2"x3/4" sharkbite tee. Then get a 3/4" hose bibb. Shut off water supply to the house. Drain the water a little from the system so you don't make a mess. Then either use a pipe cutter or hacksaw to cut the cold line leading to your faucet. Insert the sharkbite between the 2 pipes and push them into the fitting. Then push the 3/4 hose bibb into the remaining side of the tee. Then you're done!

 

[Soren]

Almost positive. There's literally nothing to grab to even screw it out. It's completely seamless as far as I can tell.

I am pretty sure I can see the way it is installed, but it may take a special tool for removal. Note the rim with the protrusions like a castle-nut just inside the outer chromed main faucet.

 

[Jekyl]

1/2" x 1/2" x 3/4" Sharkbite Style PUSH FIT Tee Lead Free Brass - PEX GUY | eBay

These PEX GUY 1/2″ x 1/2″ x 3/4″ Push-Fit Tee can be used as a connection between two lines of 1/2″ PEX piping, Copper piping, or CPVC and one 3/4″ PEX piping, Copper piping, or CPVC in any combination.

www.ebay.com

 

[Soren]

Fitting is easily installable. Trying to attach to the pipe underneath the sink? Go to home depot. Get a 1/2"x1/2"x3/4" sharkbite tee. Then get a 3/4" hose bibb. Shut off water supply to the house. Drain the water a little from the system so you don't make a mess. Then either use a pipe cutter or hacksaw to cut the cold line leading to your faucet. Insert the sharkbite between the 2 pipes and push them into the fitting. Then push the 3/4 hose bibb into the remaining side of the tee. Then you're done!

@Jmunk This might be a better option in the long run anyways, since you may be able to leave the RO/DI hooked up and just use a valve to shut it off when not in use.

 

[SenorCappuccino]

If you don't have the key to unscrew then you may have to go with under the sink process. I just went through this pain. If you have a Lowe's near you look into seeing if they have any John Guest fittings that will tee off from your sink water supply.

 

[Jekyl]

Double check the hose bib or faucet you get for it. Some have just straight copper coming out. Make sure it's 3/4 or if 1/2 get the appropriate shark bite. The pipes under your sink with be 1/2

 

[Rubberfrog]

This couldn't be any easier to install.

 

[Ratherbeflyen]

Did your BRS kit come with one of these?

When I bought my BRS RODI, I used that to connect the filter to the cold water under my sink.

I would recommend doing that. Even if you're not going to leave it connected full time, add one with a shutoff valve.

 

[Storm Trooper Reefer]

another option is to look under the sink and add a t-fitting if there is no adapter for that manufacturers aerators.
Darn, should have looked at the pop-up saying there was a new post, ya, that idea above me! LOL

 

[Jmunk]

Good suggestions. That tee from BRS is exactly the one I wanted to get. They're sold out, unfortunately. Also, I DID get the aerator out, good call! Just took using my fingernails to turn it with the slots. Unfortunately, none of the adapters I got from BRS fit in that either lol.

 

[Rubberfrog]

You can find that t adapter at home depot or lowes. Go in and show them the pics posted above. It's like a $5 part.

 

[Jmunk]

You can find that t adapter at home depot or lowes. Go in and show them the pics posted above. It's like a $5 part.

I can try that, yeah. The BRS tubing for the RODI is 1/4", correct? So it's essentially just a tee with a 1/4 tubing attachment on the side.

 

[Storm Trooper Reefer]

You can find that t adapter at home depot or lowes. Go in and show them the pics posted above. It's like a $5 part.

hope it not left handed threads!

 

[Soren]

Good suggestions. That tee from BRS is exactly the one I wanted to get. They're sold out, unfortunately. Also, I DID get the aerator out, good call! Just took using my fingernails to turn it with the slots. Unfortunately, none of the adapters I got from BRS fit in that either lol.

Even though you got the aerator out, I still think the under-sink T is a better option considering the long term. With a shut-off valve, you could leave the RO/DI system hooked up all the time if you have the space to leave the system in the cabinet. Otherwise, you might be able to connect it with a simple quick-connect system. There are tons of options with this type of plumbing.