Hydra 32 intensity

[Jaco2420]

Hi everyone, I’m just wondering if there is a way to adjust overall intensity using the my ai app for hydra 32 HD lights? Or do I have to tone down the individual channels? Thanks

 

[DesertReefT4r]

If there is a way I have not found it yet. Im new to them though.

 

[lpsouth1978]

Yes, Just place 2 fingers on the screen and slide them down. This will change the intensity of all channels the same and does not effect the overall color.

 

[Thespammailaccount]

The accumulation will reduce overall intensity by a given percentage for a set amount of time. Located under the effect tap

 

[DesertReefT4r]

Yes, Just place 2 fingers on the screen and slide them down. This will change the intensity of all channels the same and does not effect the overall color.

Good to know, I will try that. Lack of instructions is my only complaint with these lights. Imalso want to figure out how to run blues only for the first and last hour of the day.

 

[lpsouth1978]

The accumulation will reduce overall intensity by a given percentage for a set amount of time. Located under the effect tap

Yes, Acclimation mode reduces the intensity by the percentage you specify for the time you choose. However this also slowly increases the intensity during that period and is meant to acclimate corals to the higher intensity slowly and automatically.

 

[lpsouth1978]

Good to know, I will try that. Lack of instructions is my only complaint with these lights. Imalso want to figure out how to run blues only for the first and last hour of the day.

to do this just add your programming point at the specified time and set the intensities you want to achieve the desired color. I have mine set to 0% all channels until 5:00am. Then I slowly have the blues increase to about 15% over the course of several hours. Finally, they have a 3 hour ramp up to my full daytime intensity of 4 hours. After 4 hours, the cycle repeats (in reverse) util it gets back to 0% @ 11pm.

 

[DesertReefT4r]

to do this just add your programming point at the specified time and set the intensities you want to achieve the desired color. I have mine set to 0% all channels until 5:00am. Then I slowly have the blues increase to about 15% over the course of several hours. Finally, they have a 3 hour ramp up to my full daytime intensity of 4 hours. After 4 hours, the cycle repeats (in reverse) util it gets back to 0% @ 11pm.

Thats what I can figure out, how to add a set point with just 1 or 2 colors/channels.

 

[lpsouth1978]

Thats what I can figure out, how to add a set point with just 1 or 2 colors/channels.

You can see my simple program here. I actually have a 4 hour ramp and 2 hour peak. In the bottom left corner of the screen you see the +, move the slider to the time you want your set point at and tap the +. Now set each channel to the desired intensity. If you only want blues, slide the other channels to 0% and leave the blues on. Once you have the settings you want, tap the check mark to save your settings.

 

[DesertReefT4r]

You can see my simple program here. I actually have a 4 hour ramp and 2 hour peak. In the bottom left corner of the screen you see the +, move the slider to the time you want your set point at and tap the +. Now set each channel to the desired intensity. If you only want blues, slide the other channels to 0% and leave the blues on. Once you have the settings you want, tap the check mark to save your settings.

Thanks. I will try it out.

 

[DesertReefT4r]

Figured it out, thanks.

 

[Thor T.]

How do you do this? I’m on the AI app. I have the hydra 32 HD’s and have my spectrum set.

Yes, Just place 2 fingers on the screen and slide them down. This will change the intensity of all channels the same and does not effect the overall color.

Nice. It works.

 

[Jaco2420]

How do you do this? I’m on the AI app. I have the hydra 32 HD’s and have my spectrum set.

Nice. It works.

Where it has the schedule graph, press with both fingers at the same time on the schedule and drag down.

 

[Backtoreefing]

Hello all, can someone let me know how to make a change to my current schedule and save it to the current setting instead of saving it as a new preset, some say click the check mark but I don’t see a check mark on my iOS phone. Thanks