IceCap Gyre 2k

[Shark.Bait]

@corey01 , I have the same tank as you and was considering only using half of the gyre and capping the other side of it. I'd place it in between the two return nozzles. Would it fit in that space and provide enough flow? I'm wondering what your thoughts on that location are.

 

[corey01]

@corey01 , I have the same tank as you and was considering only using half of the gyre and capping the other side of it. I'd place it in between the two return nozzles. Would it fit in that space and provide enough flow? I'm wondering what your thoughts on that location are.

Sorry I didn't notice your post earlier. I haven't tried this. I may when I get home just to see and let you know what happens. but I somehow don't think it would be the very best flow. might end up blasting the front center of the tank and leaving the rest in very low flow.
like I said if I have time when I get home I will try this and let you know.

 

[Esage]

I just put my 1k into my 20 gallon nuvo today. I have it on random flow maxing out at 100%. I already have better polyp extension then i had with my jabeo

You are able to run the pump at 100%? Are you keeping mostly SPS

 

[jorahx]

I just put my 1k into my 20 gallon nuvo today. I have it on random flow maxing out at 100%. I already have better polyp extension then i had with my jabeo

How do you have it at 100%?! In my nuvo 20 I have my icecap 1k at 10% and it’s still to strong and blew all the sand off one side of the tank.

 

[macnets]

How do you have it at 100%?! In my nuvo 20 I have my icecap 1k at 10% and it’s still to strong and blew all the sand off one side of the tank.

Is 10 percent the minimum? I’m trying to buy one for my nuvo 20 also but not if it’s too much flow

 

[jorahx]

Is 10 percent the minimum? I’m trying to buy one for my nuvo 20 also but not if it’s too much flow

10% only works on one setting. All other settings require 20% and are way to strong for my tank.

 

[macnets]

10% only works on one setting. All other settings require 20% and are way to strong for my tank.

Have you tried removing one of the outlet things , maybe it will decrease the flow a bit

 

[jorahx]

Have you tried removing one of the outlet things , maybe it will decrease the flow a bit

Yes. That is how my currently is set up. One side capped off. And only the forward/reverse gyre setting works as low as 10%.

So I have it set up to do 2 at 10% and than 2 seconds at 0%. So I can get a pulsing type with lower flow. It seems to be working “fine” for the lps. But four inches of sand on the end of the tank is blown out. I tried placing a rock in the sands spot to try and slow down the flow.

 

[Shark.Bait]

Sorry I didn't notice your post earlier. I haven't tried this. I may when I get home just to see and let you know what happens. but I somehow don't think it would be the very best flow. might end up blasting the front center of the tank and leaving the rest in very low flow.
like I said if I have time when I get home I will try this and let you know.

Sounds like you’re right. Ok thanks!

 

[corey01]

Sorry @Shark.Bait I totally forgot about putting the gyre against the back wall. I didn't put it back there but I did measure it. my calipers put it ~ 5.3 inches and the space between the nozzles coming to about 6.1 so you have half an inch or so of clearance you could possibly play with but dont forget the holder for the gyre pushes it out from the back glass by quite a bit. and it could interfere with the flared stock return nozzles. I still say I don't see how this would be very good flow. but if you turned it all the way down and perhaps put 2 smaller powerheads. one on each side of it on the back wall I suppose you could create quite a flow throughout the tank. ATM I am trying really hard not to disturb the tank as my new acros are starting to encrust and I would prefer not to bother them.

 

[Shark.Bait]

Sorry @Shark.Bait I totally forgot about putting the gyre against the back wall. I didn't put it back there but I did measure it. my calipers put it ~ 5.3 inches and the space between the nozzles coming to about 6.1 so you have half an inch or so of clearance you could possibly play with but dont forget the holder for the gyre pushes it out from the back glass by quite a bit. and it could interfere with the flared stock return nozzles. I still say I don't see how this would be very good flow. but if you turned it all the way down and perhaps put 2 smaller powerheads. one on each side of it on the back wall I suppose you could create quite a flow throughout the tank. ATM I am trying really hard not to disturb the tank as my new acros are starting to encrust and I would prefer not to bother them.

Awesome, thanks for looking into that for me

 

[corey01]

Awesome, thanks for looking into that for me

pretty sure you understand but just mentioning that the 5.3 inches is only measuring from the far end of the motor to the end of 1 propeller blade. you had mentioned capping off the other propeller.
just in case anyone else comes along and is confused by the measurement.

 

[Matt Carden]

3 days