pickupman66
5000 Club Member
Brandon, what side holes did you drill for the returns?
NeveSSL's 180g Mixed Reef
- Large Build
- Thread starter NeveSSL
- Start date
- Tagged users None
pickupman66
5000 Club Member
Very cool.
OP
OP
NeveSSL
2500 Club Member
- Joined
- Jul 20, 2007
- Messages
- 2,694
- Reaction score
- 253
- Location
- Kodak
- What state or country do you live in
- Tennessee
Got some more done. My brother has been a huge help.
We put two coats of Kilz Premium on the exposed OSB to give it some protection. May put a glossy coat of some paint to help with salt creep clean up over this if we have some, but I'll have to check. I also moved the RO/DI to the other side of everything since I'm having to move the sump to the left to be under the center of the tank. I got all of my Spa Flex drains cut to size and got the hole started in the wall, too.
This doesn't look like much, but it was several hours of work.
Also picked up an inexpensive LED light at Bargain Hunt for $20. Should be perfect over the 20g refugium I have planned and is the right color spectrum, or at least closer than reef LEDs. Its a BeamsWork 400 LED light. Not bad for $20!
More to come tomorrow...
Brandon
We put two coats of Kilz Premium on the exposed OSB to give it some protection. May put a glossy coat of some paint to help with salt creep clean up over this if we have some, but I'll have to check. I also moved the RO/DI to the other side of everything since I'm having to move the sump to the left to be under the center of the tank. I got all of my Spa Flex drains cut to size and got the hole started in the wall, too.
This doesn't look like much, but it was several hours of work.
Also picked up an inexpensive LED light at Bargain Hunt for $20. Should be perfect over the 20g refugium I have planned and is the right color spectrum, or at least closer than reef LEDs. Its a BeamsWork 400 LED light. Not bad for $20!More to come tomorrow...
Brandon
OP
OP
NeveSSL
2500 Club Member
- Joined
- Jul 20, 2007
- Messages
- 2,694
- Reaction score
- 253
- Location
- Kodak
- What state or country do you live in
- Tennessee
Now that I look more at that picture, I realized I plumbed the output of my RO/DI into the drain... that's not going to work! Haha! I'll fix that tomorrow.
Brandon
Brandon
bknapp
Has been left unattended
Doh!
DaveMorris
MACNA2016 Co-Chair
I hate when that happens!
OP
OP
NeveSSL
2500 Club Member
- Joined
- Jul 20, 2007
- Messages
- 2,694
- Reaction score
- 253
- Location
- Kodak
- What state or country do you live in
- Tennessee
Haha! Me, too, Dave.
Got a bit more done today. First off, fixed the RO/DI. :loco:
Also got most of the plumbing through the wall finished and the tank moved back.
.
I also picked up the wood to frame out my "platform" (for lack of a better word) that will be going above the sump and will hold my 40 breeder frag tank, a dedicated refugium if I do one, and probably my salt mixing Brute. I'm not 100% sure that's what I'll put up there, but that's what sounds good at the moment. The good thing is that the dimensions won't change either way, so I'm good to build it tomorrow and then figure the rest out.
We will also be putting a utility sink in the garage, most likely directly next to the sump. To the right of that will be my RO/DI water. Should be a great setup! My goal is minimum maintenance and what little I have to do, I want it to be convenient and easy to do so I'll actually do it.
I'll have more tomorrow if all goes well.
Brandon
More to come tomorrow!
Brandon
Got a bit more done today. First off, fixed the RO/DI. :loco:
Also got most of the plumbing through the wall finished and the tank moved back.
I also picked up the wood to frame out my "platform" (for lack of a better word) that will be going above the sump and will hold my 40 breeder frag tank, a dedicated refugium if I do one, and probably my salt mixing Brute. I'm not 100% sure that's what I'll put up there, but that's what sounds good at the moment.
The good thing is that the dimensions won't change either way, so I'm good to build it tomorrow and then figure the rest out. We will also be putting a utility sink in the garage, most likely directly next to the sump. To the right of that will be my RO/DI water. Should be a great setup! My goal is minimum maintenance and what little I have to do, I want it to be convenient and easy to do so I'll actually do it.
I'll have more tomorrow if all goes well.
Brandon
More to come tomorrow!
Brandon
Good thing you bought that 1000' roll.
OP
OP
NeveSSL
2500 Club Member
- Joined
- Jul 20, 2007
- Messages
- 2,694
- Reaction score
- 253
- Location
- Kodak
- What state or country do you live in
- Tennessee
Haha! Thanks, Rick. I'm going to come close to using the whole roll. Wasn't terribly expensive, though... worth it, IMO. I got 50' for $65 shipped... it would have been almost $150 for the same amount from Lowes! :neutral:
Its funny... my original plan was to run 3/4" braided hose from the garage to the tank, but it ended up being a lot cheaper to just run spa flex and split it to 3/4" at the tank instead.
Brandon
Its funny... my original plan was to run 3/4" braided hose from the garage to the tank, but it ended up being a lot cheaper to just run spa flex and split it to 3/4" at the tank instead.
Brandon
Last edited:
schooleyosis
2500 Club Member
Good deal on the spaflex! Keep up the good work.
OP
OP
NeveSSL
2500 Club Member
- Joined
- Jul 20, 2007
- Messages
- 2,694
- Reaction score
- 253
- Location
- Kodak
- What state or country do you live in
- Tennessee
Definitely on the spaflex! This is where I got it from: Waterway Plastics | Flex Hose 50ft 1.5" | National Pool Wholesalers Its even US made.
I'm working a half-day today and its killing me waiting for noon to roll around so I can go build my stand above my sump!
Brandon
I'm working a half-day today and its killing me waiting for noon to roll around so I can go build my stand above my sump!
Brandon
OP
OP
NeveSSL
2500 Club Member
- Joined
- Jul 20, 2007
- Messages
- 2,694
- Reaction score
- 253
- Location
- Kodak
- What state or country do you live in
- Tennessee
A bit more progress today, as promised.
My brother has helped A LOT with this build, as is demonstrated in this pic:
Finally got it built.
And over the sump.
Still have several adjustments to make and I will also be Kilzing it, but its really exciting to make it to this point! I've got to figure out how I want to plumb it, but that should be gravy after all of this.
I can't wait to get this thing running!!!!!
Brandon
My brother has helped A LOT with this build, as is demonstrated in this pic:
Finally got it built.
And over the sump.
Still have several adjustments to make and I will also be Kilzing it, but its really exciting to make it to this point! I've got to figure out how I want to plumb it, but that should be gravy after all of this.
I can't wait to get this thing running!!!!!
Brandon
