New anemone not looking good this morning

What is the best way to raise the salinity? Small water changes every half hour?
If you have a sump you, can bail out a quart of water and mix with sea water and gradually add higer salinity water slowly to sump every 1.5-2 hrs until it reaches desired number
 
Like a cup of salt to 32 oz of water. Mix as best as you can and pour somewhere where it will be able to mix, but not touch fish or corals. If you can get me the close amount of actual gallons for your tank, I have a spreadsheet I made to calculate how much salt to add to get the salinity up. I can get you a number that should get you close to the target of 1.026.

Also, are you using a refractometer or a hydrometer for testing salinity?
Refratiome
72 tank or 72 total?
the tank is 72 I am not sure if that includes the sump but I would say 5-6g in the sump
 
Refractometer sry on my phone as well ;)
 
Refratiome

the tank is 72 I am not sure if that includes the sump but I would say 5-6g in the sump
So we will say 60 gallons to be safe and additional salt can always be added.

Here are the directions. It looks like 1.023 to 1.026 will require about 4 cups, but we want to start slow.

If you have an ATO, turn it off.
Remove a quart of water from the sump. Provided it will not let the return pump suck air. mason jar works good for this.
Add in 2 cups of your salt and mix well.
Pour 1/2 of the quart of brine mix into there your drain for the tank enters the sump. This will allow it to mix well before going into the DT.
Wait 45 minutes to an hour and check salinity again. It should have jumped up a little.
Pour the other half into the same area.
Repeat the wait and recheck again.
At this point, you should be close to 1.0245 or 1.025. provided the water volume is actually 60 gallons total.
Again, we used a low number as to not spike the salinity.
if you are at 1.024, snag another quart from the sump and mix in 1 cup of salt. This is where we go with less salt to try and hit our target number.
Add 1/2 of the quart of brine to the same area we have been adding to.
Check salinity again about an hour later.
If needed add, the other half.
You will keep doing this with less salt or less brine each time after this.
Biggest thing is not to go over our target number.

When salinity is at 1.026, turn ATO back on, and let everything run as it should.

Again, You may need more salt than what I listed out, but start with less. No need to shoot the tank up to 1.030 or something.
 
I have a pitcher that I could use. It's 64oz is that too much to change at a time? Also am I taking out water from the tank or making new water?
 
I have a pitcher that I could use. It's 64oz is that too much to change at a time? Also am I taking out water from the tank or making new water?
If you can put 64 oz of watrer in there and the pump not suck air, go for it. Just change the directions I listed to add 3 cups of salt to 64 oz and only pour in about 12 or so ounces everytime you add at a bout an hour apart, just test before each addition and let the water in the system mix with the brine for a while before testing again to determine if you need to add or not.
 
If you can put 64 oz of watrer in there and the pump not suck air, go for it. Just change the directions I listed to add 3 cups of salt to 64 oz and only pour in about 12 or so ounces everytime you add at a bout an hour apart, just test before each addition and let the water in the system mix with the brine for a while before testing again to determine if you need to add or not.
16 -20 oz or so, sorry we diluted the water a lot more, so more can be added as the impact on salinity will not be as high as a quart with 2 cups lol.
 
16 -20 oz or so, sorry we diluted the water a lot more, so more can be added as the impact on salinity will not be as high as a quart with 2 cups lol.
Oh ok so I already startesixing the 32oz with 2 cups of salt should I just add more water then?
 
The water off totally white is that ok
 
Not a problem and keep us updated. If you have anymore questions just let us know. Also, post what you measure at each time you check after letting the brine mix in the display.

As for the water being white, that is fine. This si why you want to mix in the sump and pour the half in slowly. that way it can go through the sump mix with that water and gradually enter the display
 
Not a problem and keep us updated. If you have anymore questions just let us know. Also, post what you measure at each time you check after letting the brine mix in the display.

As for the water being white, that is fine. This si why you want to mix in the sump and pour the half in slowly. that way it can go through the sump mix with that water and gradually enter the display
Ok thx so much and I will keep u guys updated :D
 
I would lower temp as well. I would look into ordering some cirprofloxicin, an antibiotic used to treat sick anemones. If it does not get better I would look into running it through a cipro treatment.
 
BTA already looks alot better!

image.jpg
 

IF YOU HAD TO TAKE A REEFING EXAM, WOULD YOU PASS?

  • Yes!

    Votes: 30 44.8%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 13.4%
  • No.

    Votes: 25 37.3%
  • Other (please explain).

    Votes: 3 4.5%
Back
Top