How we got here
I decided to replace the Red Sea ATO with another option to move the ATO out of the stand and free up room. This was going great and I was complete with it. I was testing the top up when I noticed a drip from the main drain line. I thought maybe I had dripped some water as part of the ATO work since I pulled the ATO hose through the stand hole just behind the drain.
I looked at it more closely and I could see that the water was swelling around the coupler and had a slight drip to it. I gave it a small turn and I could tighten it by hand. Thinking it had come loose I gave it a bit more of a turn. This is when I had that tell tale sound of plastic snapping that you know is going to ruin the rest of your day.
I pulled the main drain off and i swapped the overflow drain over to the main drain. This didn't fix the problem. I can tighten the plastic nut on the main drain enough that it tightens and gets tight enough that I am concerned that I would snap that nut as well so I don't want to try any tigher. Beyond that, the joint has an O-Ring. I shouldn't have to tighten it that tight to get a seal. The O-Ring should do it.
What can I do about it/Options
I purchased this tank on 31/DEC/2021 so it is only a few months old. My first plan is to call Red Sea Monday morning and see what they recommend. I do not have a lot of faith they are going to provide any remedy for me that will help. I am going to hedge towards they will say it is user error and it is on me to fix. So, how do I fix it.
I thought about just filling the entire fitting with silicone and sealing it that way. I am concerned with doing this since it may not work and I still have a problem to solve. If I did go this route I think i would do it with new pieces and move to a better gate valve.
I can probably replace the entire fitting, it does have a nut on the bottom of it. I don't know how I would find a tool large enough to fit it. Does anyone have a guess as to the size of socket it might need. How would I even replace it. I assume I have to remove all the plumbing and that is going to be a problem but I guess it may be the only option.
I have thought about doing something similar to above where I would replace the nut/connector only but swap the two drains around so that this one is the emergency overflow and I move the main drain to the center one. This would allow me to silicone the fitting together but it would be the emergency drain. I don't know how this helps though, since I have to tear the plumbing out from inside the tank and this is going to have more potential issues.
I don't know any good answers to this problem now so if you have some thoughts please share them. This is how I am "fixing" the leak at this time but I also have to run the valve fully open, any back pressure causes it to leak more. Of course this also means I have the most enjoyable gurgle to live with.
One thing I am thinking about doing is buying a siphon overflow. The point for doing this would be to hang it off the front of the tank lower than the current overflow. This would allow me to keep the tank running, but not use the rear overflow and buy me some time to solve the bigger problem. Thoughts on this?
I really do appreciate any help or ideas you can throw at me. I am not excited about having a problem like this 3 months into my tank setup.
I decided to replace the Red Sea ATO with another option to move the ATO out of the stand and free up room. This was going great and I was complete with it. I was testing the top up when I noticed a drip from the main drain line. I thought maybe I had dripped some water as part of the ATO work since I pulled the ATO hose through the stand hole just behind the drain.
I looked at it more closely and I could see that the water was swelling around the coupler and had a slight drip to it. I gave it a small turn and I could tighten it by hand. Thinking it had come loose I gave it a bit more of a turn. This is when I had that tell tale sound of plastic snapping that you know is going to ruin the rest of your day.
I pulled the main drain off and i swapped the overflow drain over to the main drain. This didn't fix the problem. I can tighten the plastic nut on the main drain enough that it tightens and gets tight enough that I am concerned that I would snap that nut as well so I don't want to try any tigher. Beyond that, the joint has an O-Ring. I shouldn't have to tighten it that tight to get a seal. The O-Ring should do it.
What can I do about it/Options
I purchased this tank on 31/DEC/2021 so it is only a few months old. My first plan is to call Red Sea Monday morning and see what they recommend. I do not have a lot of faith they are going to provide any remedy for me that will help. I am going to hedge towards they will say it is user error and it is on me to fix. So, how do I fix it.
I thought about just filling the entire fitting with silicone and sealing it that way. I am concerned with doing this since it may not work and I still have a problem to solve. If I did go this route I think i would do it with new pieces and move to a better gate valve.
I can probably replace the entire fitting, it does have a nut on the bottom of it. I don't know how I would find a tool large enough to fit it. Does anyone have a guess as to the size of socket it might need. How would I even replace it. I assume I have to remove all the plumbing and that is going to be a problem but I guess it may be the only option.
I have thought about doing something similar to above where I would replace the nut/connector only but swap the two drains around so that this one is the emergency overflow and I move the main drain to the center one. This would allow me to silicone the fitting together but it would be the emergency drain. I don't know how this helps though, since I have to tear the plumbing out from inside the tank and this is going to have more potential issues.
I don't know any good answers to this problem now so if you have some thoughts please share them. This is how I am "fixing" the leak at this time but I also have to run the valve fully open, any back pressure causes it to leak more. Of course this also means I have the most enjoyable gurgle to live with.
One thing I am thinking about doing is buying a siphon overflow. The point for doing this would be to hang it off the front of the tank lower than the current overflow. This would allow me to keep the tank running, but not use the rear overflow and buy me some time to solve the bigger problem. Thoughts on this?
I really do appreciate any help or ideas you can throw at me. I am not excited about having a problem like this 3 months into my tank setup.

