pH toooooo low!
- Thread starter d2mini
- Start date
- Tagged users None
Velcro
2500 Club Member
I had an old model. He must have started lowering the Venturi port?
Randy Holmes-Farley
Reef Chemist
Staff member
Super Moderator
Excellence Award
Expert Contributor
Article Contributor
R2R Research
My Tank Thread
Weeks to raise pH with outside air? The effect should happen in a day or two max.
Velcro
2500 Club Member
Yea I’ve always seen improvement with 12 hours and full effect with 48 hours.
Velcro
2500 Club Member
Another consideration is that often the air right outside the home is still high in CO2. I saw a huge difference between drawing air just outside the window and then drawing air about 12 feet up from the window.
OP
OP
d2mini
5000 Club Member
I think it's still the same. I'm talking extreme circumstances.
Like right now I'm having an issue with my Vectra fluctuating flow, which causes the sump level to change. If it gets high, the skimmer start filling the cup real quick.
Velcro
2500 Club Member
bubbaque
Follow me on Instagram @ Bubbaquecorals
The float switch to your controller might really be worth it to you. The moisture for the media really makes that big of a difference. I initially have it pulling humidity from a 5 gallon bucket half full of water and it helped make it last slightly longer. Once I put the input into the skimmer cup it made a world of difference on the life of it.
I did end up turning off my return pump one day and not my skimmer and it did flood the media but luckily I noticed right away when it was happening and stopped it. I removed the hose to skimmer ever since. I don't have a controller to control any of this so it wasn't really an option for me to add the float switch or it would have been worth while to install it and keep the hose in it.
I did end up turning off my return pump one day and not my skimmer and it did flood the media but luckily I noticed right away when it was happening and stopped it. I removed the hose to skimmer ever since. I don't have a controller to control any of this so it wasn't really an option for me to add the float switch or it would have been worth while to install it and keep the hose in it.
Want2BS8ed
Active Member
Wow, that is an awesome thread as well, between that and what we have discussed here I am going move my intake to the collection cup to see if the media can be extended even further than the solenoid bypass alone.
Recirculating the same air - brilliant!
Greater piece of mind and much easier than plumping outside and running carbon.
Dennis, you start some of the most thought provoking threads. Thanks!
M
OP
OP
d2mini
5000 Club Member
ok so last night was a PITA.
First, i had my Vectra return pump soaking in a vinegar bath because I'm having a whole other problem with that.
So the tank recirculation was off for about 6 hours which dropped the ph below 7.
Then after I get the pump cleaned, put back together and flowing again, I realize like an hour later that my skimmer is not working. Inspected the pump first, couldn't find anything.
Finally took the skimmer apart and found a litte snail jammed up in the venturi. :mad:
Got that put all back together and running by 9pm. Yeesh.
But that includes drilling the skimmer cap hole a little larger and shoving a 1/4" ro/di line in there. I ran it out the back of the stand. So it's poking out the rear corner.
It took quite a while of the ph to rise and is currently at the same value of 7.57.
Will see if it gets any higher today than normal.
First, i had my Vectra return pump soaking in a vinegar bath because I'm having a whole other problem with that.
So the tank recirculation was off for about 6 hours which dropped the ph below 7.
Then after I get the pump cleaned, put back together and flowing again, I realize like an hour later that my skimmer is not working. Inspected the pump first, couldn't find anything.
Finally took the skimmer apart and found a litte snail jammed up in the venturi. :mad:
Got that put all back together and running by 9pm. Yeesh.
But that includes drilling the skimmer cap hole a little larger and shoving a 1/4" ro/di line in there. I ran it out the back of the stand. So it's poking out the rear corner.
It took quite a while of the ph to rise and is currently at the same value of 7.57.
Will see if it gets any higher today than normal.
Velcro
2500 Club Member
Tank pH below 7.0? I don't think that's possible!
OP
OP
d2mini
5000 Club Member
Yup. While the sump was sitting stagnant (where my probes are) it was reading 6.5.
Once it got going the sump water had to mix with the tank water... whatever that was at the time.
GoVols
Cobb / Webb - 1989
Reef Squad Leader
Excellence Award
Reef Tank 365
MTRCMember
Article Contributor
Hospitality Award
R2R Research
My Tank Thread
OP
OP
d2mini
5000 Club Member
Like I said in my first post........
............ ;Wideyed
Brew12
Electrical Gru
Wow! That must be some crazy interaction with the calcium reactor! CO2 alone couldn't do that!
OP
OP
d2mini
5000 Club Member
I had the c02 solenoid and feed pump unplugged while the return pump was down. Basically nothing in the sump was running. Only the display had circulation from the vortechs.Wow! That must be some crazy interaction with the calcium reactor! CO2 alone couldn't do that!
Velcro
2500 Club Member
Man that's really weird...
Velcro
2500 Club Member
Dennis, take a cup of your tank water outdoors and aerate the hell out of it for a few hours. Remeasure the pH with your controller to see what that says. I'm really starting to think there's a calibration of equipment malfunction going on here. I don't think saltwater with appropriate alk can even get that low from CO2 alone (at least the levels in the ambient air).
OP
OP
d2mini
5000 Club Member
Will do.
Brew12
Electrical Gru
I'm not a calcium reactor guy, and I know they work at pH's down in the 6.5 range since they use carbonic acid to do the dissolving. I just can't figure out how it could drop the entire sump that low if it wasn't running.
Calibration could be an issue, but that would have to be WAY off since pH is a log scale.
