reef-pi :: An opensource reef tank controller based on Raspberry Pi.

[Michael Lane]

From my primitive understanding, we can use reef-pi as it is, with stepper motors. We have to connect pi or pca9685 pwm pin to a stepper drivers (such as drv8835) and that should be it.
Reversing the motor direction is very common. The titration systems definitely use those capabilities. From a manufacturing and electronics perspective, H-brige drivers (a type of circuit that allows easily switch the polarity of motors) are very common and omnipresent in most stepper/dc motor equipment. I guess from manufacturing point of view its hard to know if this feature will be used or not, but given the prevalence (and cheap) of this capability, its safer to just have it.
It will be awesome if @theatrus, @Bigtrout or @Michael Lane can validate my assumption, beforer i embark on testing this setup ;-)

It sounds like you have it right. Stepper motors are driven by alternating magnetic fields, so it's a bit more complicated than using a DC motor. The stepper driver will control moving those fields with each pulse.

 

[Ranjib]

It sounds like you have it right. Stepper motors are driven by alternating magnetic fields, so it's a bit more complicated than using a DC motor. The stepper driver will control moving those fields with each pulse.

As I am reading through, it seem like the duty cycle does not matter that much (anything above 50% is good) and I have to actually change the pwm frequency to change the speed of the stepper motor. I am ordering a DRV8825 driver and that 33$ stepper motor based doser for testing. Thanks for checking . I'll keep you all posted

 

[MrWheelock]

Can't wait to see the results. I was thinking about using those instead of gutting a slave doser unit. Looks like those are wire for +/- in one direction and +/- in reverse direction. Is there any reason to wire "reverse"? I don't imagine I'd ever need to draw water from the tank....

Auto water change

 

[Ranjib]

I am afraid @theatrus is not engaged with reefing for a while now. Perhaps he’s busy, I hope for that and not health issues, or anything else.

Hmm.. Life can get busy.

 

[buddy.]

Does anyone know what this email alert is caused by? The probe is still working so I am not sure why it says it failed.

 

[AbjectMaelstroM]

Does anyone know what this email alert is caused by? The probe is still working so I am not sure why it says it failed.

Looks like it's no longer registering the temp probe labeled "sump".

Check connections/probe, could be a dead probe.

 

[buddy.]

Looks like it's no longer registering the temp probe labeled "sump".

Check connections/probe, could be a dead probe.

The weird thing is that the probe never actually stops working according to my graphs on the dashboard.

 

[AbjectMaelstroM]

The weird thing is that the probe never actually stops working according to my graphs on the dashboard.

Does it actually register temp changes or displays the same temp it read last? When I was playing around with my build, I saw that same message when I disconnected Temp probes with pi running. It continued to display temp reading, but it didn't register changes, but continued the last temp reading.

I would check make sure the probe is functional and registers temp changes.

 

[Ranjib]

Some updates on the wave maker test. On a sad note, the 12V submercible pumps were not variable speed. They didnt run on PWM signal. I dont know if they would rather respond to analog (0-12V) or they are just fixed speed. I'll figure it out later, if they do work in analog speed, I'll take the analog path on ciruit side.

But even without the PWM support, I was able to kinda use those pumps straight by supplying entire 12V. The way I did was pretty simple, just disable pwm module in kernel config, declare GPIO 18 and 18 (which is feeding L293d en1/en2 pins) as normal outlets in reef-pi and instead of pwm profile, use timers. Though I dont have the variable speed features, now with switching offloaded to l293d, I can do lot more aggressive (5 or 15 second pulses) without worrying about relay's failing or click noises. I am planning to use this as wavemekar, as intended, but with times instead of pwm profiles. I have tested my dosing heads also, and they work just fine. Which means I can use this exact controller to control any two dosing pumps. All of this will only involve couple of software tweaks. The hardware/circuit/enclosure is reusable as it is. I like this.

Pumps:

Build

Tank and pumps (ignore the clutter )

The dosing unit

I made a handy male -male barrel connector for pump or dosing unit
Off to the next set of things ...

 

[Ranjib]

Does anyone know what this email alert is caused by? The probe is still working so I am not sure why it says it failed.

It means the sensor reading has failed crc check. Sometime this happens due to bad probe or connection issue , which results in data corruption causing failure in checksum . Pi indicates this by “yes” when checksum verification pass. Reef-pi is just showing that error , and complaining that it’s expecting a yes at the end of the reading file. This also means the sensor is present and detected , and reef-pi is also able to read it.

 

[buddy.]

It means the sensor reading has failed crc check. Sometime this happens due to bad probe or connection issue , which results in data corruption causing failure in checksum . Pi indicates this by “yes” when checksum verification pass. Reef-pi is just showing that error , and complaining that it’s expecting a yes at the end of the reading file. This also means the sensor is present and detected , and reef-pi is also able to read it.

Thanks @Ranjib . Do you mean a physical wiring connection or something to do with the data connecting?

I am also getting these email alerts occasionally. Also sometimes a negative temperature of something silly like -1000 degrees. Temps are in C.

Here is my temperature page in reef-pi. Does it look correct? Just ignore all of the graph before the heater readings, this was when I had a failed probe. You can see the spike where it alerted me to 85 degrees.

 

[Bigtrout]

Those spikes look similar to what i was getting when i had the wonky power supply throwing interference.

@Ranjib means the data is getting corrupted occasionally. This could be from loose wiring, or some type of interference. Check and double check the wiring. Also check the routing of your sensor wiring. Keep it away from any AC wiring or motor/pump wires.

 

[burningbaal]

Anyone know of a black box LED that is controllable? I want to get a few black box LEDs for my future 180g, but want to be able to ramp each unit (expecting 3-6 of them, depending on wattage) up individually, and to control an actinic type apart from the daylight. two channels would be fine for me, I just want to control the brightness of each of the two channels individually so I can get a white sunrise, then bring in the blues, then ramp the whites down for dusk and run a little blues until my bedtime

 

[Ranjib]

Anyone know of a black box LED that is controllable? I want to get a few black box LEDs for my future 180g, but want to be able to ramp each unit (expecting 3-6 of them, depending on wattage) up individually, and to control an actinic type apart from the daylight. two channels would be fine for me, I just want to control the brightness of each of the two channels individually so I can get a white sunrise, then bring in the blues, then ramp the whites down for dusk and run a little blues until my bedtime

There are several posts here in r2r on controlling viparspectra and mars aqua lights using reef-pi, search for those

 

[Schreiber]

There are several posts here in r2r on controlling viparspectra and mars aqua lights using reef-pi, search for those

Here's a couple worthwhile reads.

Mars Aqua led light

Mars Aqua led light I have 5 of them want to make them dimmable with a Raspberry pi. will a PCA9685 16-channel 12-bit PWM servo driver do this or do i have to convert to analog for it to work. I tried the reef-pi setup for Kessil leds and the light will not dim I wired the lights the way they...

www.reef2reef.com

Mars Aqua Chinese black box PWM Converter

The Mars Aqua lights have been out for a pretty long time, and there are already plenty of examples of modding them to be controlled with 0-10v analog or pwm. They usually seem to be destructive and still require a timer to actually turn the lights on and off. I came up with the following...

www.reef2reef.com

 

[zab34]

So going to venture into a reefpi build. I want to use one of ML Hats but it looks like v3 is sold out.

Will I have any limitations going with a v2? Will I encounter any limitations with a pi zero vs a pi 3?

Any builds you would recommend that used the ML hat.

Ideally I would like:

Relay power control
ATO from float sensors
Temperature monitoring and heater control
Macros for feed and water change

 

[AbjectMaelstroM]

So going to venture into a reefpi build. I want to use one of ML Hats but it looks like v3 is sold out.

Will I have any limitations going with a v2? Will I encounter any limitations with a pi zero vs a pi 3?

Any builds you would recommend that used the ML hat.

Ideally I would like:

Relay power control
ATO from float sensors
Temperature monitoring and heater control
Macros for feed and water change

The V2 hat has exactly the same functions as the V3 hat, the only difference being smaller connectors and Status LEDs on the board. For longevity, that V2 hat is the way to go.

I have to V2 hats and it is an awesome product and will easily be able to implement the functions like you listed.

As far as Raspberry Pi zero vs The 3B, if you are going to run it as a headless unit without a ton of sensors and equipment, the zero will work just fine. 3B just has more muscle and LAN capability.

I use 3Bs with my build.

 

[PHopkins]

I just installed reef pi on a rasberry pi zero w. When i try and test the jack for the pwm control I am getting the error message

{"error":"Failed to update. Error: write /sys/class/pwm/pwmchip0/pwm0/period: invalid argument"} | HTTP 500

When I try and change User name and Password it is giving me this error

Failed to initialize i2c. Errorpen /dev/i2c-1: no such file or directory

any help getting this working would be greatly appreciated

 

[Ranjib]

Here's a couple worthwhile reads.

Mars Aqua led light

Mars Aqua led light I have 5 of them want to make them dimmable with a Raspberry pi. will a PCA9685 16-channel 12-bit PWM servo driver do this or do i have to convert to analog for it to work. I tried the reef-pi setup for Kessil leds and the light will not dim I wired the lights the way they...

www.reef2reef.com

Mars Aqua Chinese black box PWM Converter

The Mars Aqua lights have been out for a pretty long time, and there are already plenty of examples of modding them to be controlled with 0-10v analog or pwm. They usually seem to be destructive and still require a timer to actually turn the lights on and off. I came up with the following...

www.reef2reef.com

Thank you @Schreiber :hugs:

 

[Ranjib]

I just installed reef pi on a rasberry pi zero w. When i try and test the jack for the pwm control I am getting the error message

{"error":"Failed to update. Error: write /sys/class/pwm/pwmchip0/pwm0/period: invalid argument"} | HTTP 500

When I try and change User name and Password it is giving me this error

Failed to initialize i2c. Errorpen /dev/i2c-1: no such file or directory

any help getting this working would be greatly appreciated

Enable i2c using raspi-config, and reboot. Which version you are using? use 2.5 if you are unsure.