RODI sat still for three months, still okay?

Thought so, they look very clean in that photo. Too bad it's not November, a 3-sensor inline TDS meter and pressure gauge from BRS would make great Christmas gifts. Birthday coming up perhaps? :)
My fiancées....maybe I’ll get her that, if I want a kick in the butt. Hey is there a way to flush the water out of the unit, so tap doesn’t just sit in there?
 
I would 100% use it for many reasons.
#1 it’s for the tank cycling
#2 I have rinsed mold smelling sand that has turned grey and smells like garbage with tap water and am using that sand today
#3 it’s unlikely anything that’s gonna harm the tank is in that water
#4 I arguably have had RODI water sitting in the same brute containers for over a year cuz I never fully drain and or rinse out my brute bins they always have rodi water in them

Good luck!


Agreed. Since the tank is cycling, wouldn't worry much about it. You'll prolly do a couple of water changes before livestock sees the tank anyway.

EDIT: Water looks fine from the pictures. The debris you see is "normal", to the extent that crap always somehow finds its way to my storage containers as well. I would be more worried with smells and or strange films.
 
I would use it if it tests ok. I had some similar stuff in my storage when I had my 100g sometimes I would recirculate with a sock on the output after stirring up.
 
Hey guys, thanks everyone for the replies. Honestly I think it would have been okay to use, mainly because I am just cycling the tank. However I just dumped it, it’s taken this long to get this build going, why rush it now.

Again, can I drain the water that sits in the RODI unit? I’ve heard of flushing them, not sure how though.
 
Hey is there a way to flush the water out of the unit, so tap doesn’t just sit in there?

There's a fair amount of additional things you can do if you want the best RODI water, beyond the basic setup and the two things I already mentioned.

First, flushing is useful. When you 'flush the membrane', you temporarily remove the back pressure, allowing the water to rush quickly through the input water side of the membrane and down the drain, taking any debris or ions that may have accumulated on the membrane with it. It's easy to install a flush valve; BRS has those too. There are different opinions on how often to flush, but you probably can't do it too much.

In fact, here's a combo package from BRS that has everything I've mentioned so far. That company makes it pretty easy.

Another issue that keeps you from getting the purest RODI water possible is what happens when water sits in the membrane cartridge after the input water has been turned off for a while. As it sits, quite a bit of TDS will migrate across the membrane into the product water. This happens quickly, within a few hours. Then, when you turn the system on again to generate more water, the TDS gets pushed into your DI filter, where it may or may not get entirely removed, and even if it does, the life of your DI resin is shortened considerably. The solution to this is to install a 3 way valve on the product water output of the membrane, with one branch to the DI resin and the other branch to the drain. Drain off the first minute or so of water generated by the membrane after each new startup, then switch it over so it goes to the DI resin. Of course BRS has what you need here too. (With the TDS meter, you can actually watch the membrane output clear of TDS and thus know exactly when to switch it over. )

This may seem like some hassle, but I can attest that it all really makes a difference. Before I installed that last valve, I would get TDS values of 0 on the meter in my product water, but yet ICP-OES testing of the same water would show that traces of this and that (primarily silicate) still got through. After adding that valve and using it consistently, traces of contamination have vanished.

Edit: For another layer of quality, you can also add a second DI resin canister after the first one. Something like this with one of these works fine. It provides an extra polish, and you can exhaust nearly the entire amount of resin in the first canister before refilling it, without concern about breakthrough contamination. Good idea to rotate the cartridges when you refill the exhausted one.
 
Last edited:

IF YOU HAD TO TAKE A REEFING EXAM, WOULD YOU PASS?

  • Yes!

    Votes: 30 44.8%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 13.4%
  • No.

    Votes: 25 37.3%
  • Other (please explain).

    Votes: 3 4.5%
Back
Top