I Received a NEW Trident NP Nitrate & Phosphate Tester!!!!

Ok...so....here is an update:

I dosed 2 capfuls of neophos about an hour or so before the NP did it's reading today. It should raise the Phos by about 0.02 based on the formula on the bottle.

Yesterday the NP measured 0.04...today it measured 0.05.
Yesterday the Hanna got 0.02...today it measured 0.07.

Technically I guess both sets of numbers are within the Hanna ULR tolerance of 0.02. Also..."technically" if I dosed enough NeoPHos to raise my tank 0.02 but the NP only registered 0.01 increase ...that's still probably within the tolerance range for the NP

I dosed 1/8th tsp of Sodium Nitrate which should have raised my Nitrate by about 1.4

Yesterday the NP measured 4.4...today it measured 5.6
Yesterday the Hanna got 3.7..today it measured 4.8

Overall I feel pretty confident in the Nitrate measurements. I don't feel that way about the Phosphate numbers but with the numbers being so small and the tolerances being what they are...it's probably "accurate".

I was worried my NP Phosphate numbers were heading down to 0.0 like others have posted...but it did see to move back up with my dose today.

Unrelated - you wrench on the Eagle?
 
Nope...flew in the back seat. That's me and my driver over someplace sandy.

Ah, got it. I wrenched on them for a spell. Not the E's but C and D's overseas. Great airframe and avionics package.

Didn't mean to derail thread - just caught my attention :D
 
Got complacent in trusting my np. Was reading spot on for a few weeks. Now my phos snuck back up and have to play catch up again. Really annoying its still meh at this point
 
Mine was running great for a month or so, then I had to switch reagents... ugh. Now phos reading off by over 0.1 to the high side. Another ticket into support =/
 
Mine was running great for a month or so, then I had to switch reagents... ugh. Now phos reading off by over 0.1 to the high side. Another ticket into support =/

Same, i tried a reset didnt fix anything
 
Mine was running great for a month or so, then I had to switch reagents
Have you been monitoring the reagent lot numbers? My PO4 test results were significantly off at .14 when initially set up. I've just begun using a second set of reagents and now the tests match Hanna's .05 results without any calibration. However, both the first and second sets of reagents share the same lot number, which is puzzling.

Have you considered rerunning the reagent replacement task on the same batch to check for any changes in the readings? It might alter the indicated levels of remaining reagents, but could it be worth the attempt?
 
Have you been monitoring the reagent lot numbers? My PO4 test results were significantly off at .14 when initially set up. I've just begun using a second set of reagents and now the tests match Hanna's .05 results without any calibration. However, both the first and second sets of reagents share the same lot number, which is puzzling.

Have you considered rerunning the reagent replacement task on the same batch to check for any changes in the readings? It might alter the indicated levels of remaining reagents, but could it be worth the attempt?
Yeah retried the replacement task again and no change. Bit the bullet today after not hearing back from support and ended up replacing the 2 week old reagents with new ones. First test and we are back to good. So things are pointing at bad reagents at this point. So user be aware, there might be a bad batch out there.
 
Bit the bullet today after not hearing back from support and ended up replacing the 2 week old reagents with new ones. First test and we are back to good. So things are pointing at bad reagents at this point. So user be aware, there might be a bad batch out there.
What was the lot# on these?
 
What was the lot# on these?
IMG_9608.jpeg

1-2-3 from left to right. I’m not 100% certain but I believe reagent three is phosphate.
 
IMG_9608.jpeg

1-2-3 from left to right. I’m not 100% certain but I believe reagent three is phosphate.
Same lot#'s that I have. 1st set tested PO4 high, 2nd set tested good.....to hanna. All same lot.

I'm thinking it has something to do with the little bottle that is mixed in to reagent 3. I don't have mine anymore, but I don't remember seeing a lot# on it either.
 
Same lot#'s that I have. 1st set tested PO4 high, 2nd set tested good.....to hanna. All same lot.

I'm thinking it has something to do with the little bottle that is mixed in to reagent 3. I don't have mine anymore, but I don't remember seeing a lot# on it either.
Could be, but def my issue points to reagents. I inquired to NS for replacements and so far no response.
 
Could be, but def my issue points to reagents. I inquired to NS for replacements and so far no response.

I have messaged Neptune about my NP a couple days ago and just got a response last night. They had me give them logs.
 
I also submitted an honest review of the Trident NP to BRS's website over a month ago, and it was never approved.
 
I installed the replacement Trident NP and new reagents from Neptune last night. Crossing my fingers for round 2. If yesterday's test and this morning's second test are any indications, it does not look promising for PO4 results as the results are very similar to the return unit so far. Firmware has been updated. I just did factory defaults and restart trident in preparation for tomorrow's automated test. Keeping my fingers crossed but this isn't fun if this continues :angry-face:

1726518449046.png

...really .5 PO4?

Having shared that, I will also share that the customer service is excellence. They look to be doing their best and the senior support person and others have been good to work with.
 
Having shared that, I will also share that the customer service is excellence. They look to be doing their best and the senior support person and others have been good to work with.

I haven't been able to get support to reply to my emails in almost 10 days now.
 
I had to ask to see if they even got my reply. I think ghey must be pretty swamped.
Yeah I sent them the file they wanted. And heard nothing. Then 3 additional emails asking if they got any of my responses. Nothing.
 
Yeah I sent them the file they wanted. And heard nothing. Then 3 additional emails asking if they got any of my responses. Nothing.
I sent my file a week ago, my rep said he would check with engineers but no word. I’m just annoyed im wasting $30 a month in reagents on it lol
 
I sent my file a week ago, my rep said he would check with engineers but no word. I’m just annoyed im wasting $30 a month in reagents on it lol
My first unit was RMA’d. after my first reagent change my phosphate went 70ppm off and phos only reads 0. The second unit has been running for a week now with identical readings as the first unit, same reagents. I emailed Neptune asking for a set of reagents since I’ve entirely wasted this batch and that I think it’s worth while to try different reagents. They ignored my request and had me send them the logs requested when the first unit was RMA’d about to try to force a refund at this point.
 

IF YOU HAD TO TAKE A REEFING EXAM, WOULD YOU PASS?

  • Yes!

    Votes: 30 44.8%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 13.4%
  • No.

    Votes: 25 37.3%
  • Other (please explain).

    Votes: 3 4.5%
Back
Top