Red Sea Reefer and Klir Filter

[Thor2j]

I have the Red Sea Reefer 350 with the V3 sump, which measurements would you need to create a 3D design for it?

Completely different from the 525 and 450 v1 and v2. Wouldnt attempt to do it without a sump here to play with.
Sorry

 

[Thor2j]

So is anyone making these adapters for sale? I have a 525 XL and a Klir filter I was using on my old set up so would love to still be able to use the Klir filter.

Do you have one or 2 klir units??
What return pump do you have and do you know your exit tank flow??

 

[xilni]

Completely different from the 525 and 450 v1 and v2. Wouldnt attempt to do it without a sump here to play with.
Sorry

Ok, so for guidance if I attempt this myself, the goal is to block off the other opening and create one 4in opening for the Klir?

 

[Thor2j]

Ok, so for guidance if I attempt this myself, the goal is to block off the other opening and create one 4in opening for the Klir?

Depends on your flow. The real goal is to build a wall that will allow the water to rise in order to trigger the water level sensor.

 

[xilni]

Depends on your flow. The real goal is to build a wall that will allow the water to rise in order to trigger the water level sensor.

Ok, so I’ll need to create a raised wall on the side the tray normally pulls out of to raise the water level in that area when the roller mat clogs to trigger the water level sensor? I think the glass side walls of the filter tray area are high enough.

 

[Thor2j]

Ok, so I’ll need to create a raised wall on the side the tray normally pulls out of to raise the water level in that area when the roller mat clogs to trigger the water level sensor? I think the glass side walls of the filter tray area are high enough.

Yes, you have to be able to raise the level in the area where the klir filter will be sitting.

 

[psionic619]

Is there any way to lower the sensor instead of raising the water level?

 

[Palluk33]

Can someone make a adopter for reefer 350 with v2 sump?

 

[TX_Punisher]

Anyone running these on the 750xxl?

 

[Hnguyen]

Have prototype for my reefer 525xl. Still need to tweek a few things but the majority of it is all set. Will have it up and running middle of next week when I get back in town.

Do you happen to have the STL file you're willing to share?

 

[Thor2j]

Do you happen to have the STL file you're willing to share?

No, sorry.

 

[Palluk33]

Have to knock on wood I’m running klir di-4 for in me Red Sea Reefer 350 V2 sump for 2 weeks with out any problems and I’m loving it.

 

[Mario P.]

Have to knock on wood I’m running klir di-4 for in me Red Sea Reefer 350 V2 sump for 2 weeks with out any problems and I’m loving it.

I have the same reefer 350 tank and sump. did u make the adapter in your pics? im looking at using a Klir on my system

 

[Palluk33]

I have the same reefer 350 tank and sump. did u make the adapter in your pics? im looking at using a Klir on my system

Yes I 3D print them

 

[TX_Punisher]

How long are yalls rolls lasting?

 

[CDavmd]

Yes I 3D print them

I have a 425xl- wonder if the printed part for the 350 would work. I think sumps are the same but I could be wrong.

Is the file on thingsverse?

Thanks!

 

[Palluk33]

I have a 425xl- wonder if the printed part for the 350 would work. I think sumps are the same but I could be wrong.

Is the file on thingsverse?

Thanks!

The sump is different and will not fit right, other member have files for reefer 450 check the forms

 

[CDavmd]

The sump is different and will not fit right, other member have files for reefer 450 check the forms

Thanks but I have the 425xl not 450. The 425xl is the same tank as the 350 but just a couple inches deeper front to back

 

[TLeTourneau]

I had an issue with the motor not being able to turn the roll. I opened a ticket and Coral-Vue replaced the motor assembly under warranty, great service! The new motor is significantly larger than the original motor and doesn't seem to have any issue turning the roll.

 

[Tampa Reefer]

Anybody make one for the 425xl?