ATTN: ALL MAJOR POWERHEAD MANUFACTURERS

  • Thread starter Thread starter tsav87
  • Start date Start date
  • Tagged users None
I think the best way to make a prototype would be to scavenge a MP40 and create a new wetside with a u joint. You can even use their magnet and prop (already sized for the motor) Just create a way to connect them with a u-joint. Of course that would only be for personal use. If you wanted to sell them, you would need to make sure the new model was different enough to not infringe on their patent. I am not a patent lawyer, but I imagine adding an articulating wet side may be enough of a change to warrant a new patent.
 
I've got the solution for insufficient power......a flux capacitor.....1.21 gigawatts of power! :rolleyes: That there's an invention,...a flux capacitor powerhead!!! :eek::D
 
I've got the solution for insufficient power......a flux capacitor.....1.21 gigawatts of power! :rolleyes: That there's an invention,...a flux capacitor powerhead!!! :eek::D
giphy.gif
 
Theoretically pure water with 0 TDS could conduct electricity very well, buy you cant direct which way it travels through water. @Brew12 involved.

Actually, you need the stuff in water to conduct electricity. So 0 tds would not conduct.
Kids, don't try this at home.
 
I think the best way to make a prototype would be to scavenge a MP40 and create a new wetside with a u joint. You can even use their magnet and prop (already sized for the motor) Just create a way to connect them with a u-joint. Of course that would only be for personal use. If you wanted to sell them, you would need to make sure the new model was different enough to not infringe on their patent. I am not a patent lawyer, but I imagine adding an articulating wet side may be enough of a change to warrant a new patent.
Unfortunately, that won't work. For the Vortech to work properly the dry side needs to stay parallel to the wet side and they need to stay close together. An MP10 will barely work on 3/4" glass.
 
I Maybe over thinking this, would there be a biological effect with running magnetic fields into the tank directly?
 
Actually, you need the stuff in water to conduct electricity. So 0 tds would not conduct.
Kids, don't try this at home.
I missed that and you are absolutely correct. I use RODI water for cooling on a 35kV system at work because it is an excellent insulator.
 
Unfortunately, that won't work. For the Vortech to work properly the dry side needs to stay parallel to the wet side and they need to stay close together. An MP10 will barely work on 3/4" glass.
It would stay parallel. The propeller shaft would have a universal joint to allow swivelling of the prop while the shaft always stays perpendicular to the motor as it does now.
 
It would stay parallel. The propeller shaft would have a universal joint to allow swivelling of the prop while the shaft always stays perpendicular to the motor as it does now.
So adding a U-joint on the shaft before the propeller? That could work if it could withstand the mechanical forces! ;Bookworm
 
So adding a U-joint on the shaft before the propeller? That could work if it could withstand the mechanical forces! ;Bookworm
Titanium?
 
I Maybe over thinking this, would there be a biological effect with running magnetic fields into the tank directly?
I have a wireless phone charger about 16 inches from my head where I sleep. No worse for ware! lol
 
Unfortunately, that won't work. For the Vortech to work properly the dry side needs to stay parallel to the wet side and they need to stay close together. An MP10 will barely work on 3/4" glass.
That is the point of the U joint. Imagine the current setup, but instead of the prop attached to the shaft, have the u joint attached to it. Then you can have an articulating housing that can swing around it. Probably up to 60 degrees, and the magnet/base will stay stationary.
 
That is the point of the U joint. Imagine the current setup, but instead of the prop attached to the shaft, have the u joint attached to it. Then you can have an articulating housing that can swing around it. Probably up to 60 degrees, and the magnet/base will stay stationary.
60 degrees from center, so a 120 degree motion all together.
 
So adding a U-joint on the shaft before the propeller? That could work if it could withstand the mechanical forces! ;Bookworm

The forces are very minimal. Shoot, I have rc cars that do 100 mph with plastic u joints. I small titanium one with ceramic bearings would probably last the life of the powerhead.
 
The forces are very minimal. Shoot, I have rc cars that do 100 mph with plastic u joints. I small titanium one with ceramic bearings would probably last the life of the powerhead.
Wow!

Lets see if this works... @Terence
 
60 degrees from center, so a 120 degree motion all together.

I would think so. Even that might require multiple joints. It may be better to use a flexible shaft all together. Like the dremel tools.

https://www.lowes.com/pd/Dremel-Rot...yrB-uCjfhNB6xVAl-M2ll66G-U-Ju-DxoCDacQAvD_BwE

Obviously only an inch or two long. The secret would be to make the gimbal so that it articulates around the back center of the powerhead. If it didn't, it would change distance too much.
 
Actually, you need the stuff in water to conduct electricity. So 0 tds would not conduct.
Kids, don't try this at home.

You’re right, I said it backwards.
 

IF YOU HAD TO TAKE A REEFING EXAM, WOULD YOU PASS?

  • Yes!

    Votes: 30 44.8%
  • Not yet, but I have one that I want to buy in mind!

    Votes: 9 13.4%
  • No.

    Votes: 25 37.3%
  • Other (please explain).

    Votes: 3 4.5%
Back
Top